OOIR: Observatory of International Research

Papers

(The H4-Index of Corrosion Science is 69. The table below lists those papers that are above that threshold based on CrossRef citation counts [max. 250 papers]. The publications cover those that have been published in the past four years, i.e., from 2022-01-01 to 2026-01-01.)

Article	Citations
Insights into the fretting corrosion behavior and damage mechanism of Inconel 690TT in water and steam environments containing different dissolved oxygen levels	278
Sequence and mechanism of early microstructure evolution in alloy 690TT subjected to fretting corrosion in high temperature pressurized water	213
Early oxidation stages of austenitic stainless steel monitored using Mn as tracer	164
Editorial Board	162
Design of alkyl-substituted aminothiazoles to optimise corrosion inhibition for galvanised steel: A combined experimental and molecular modelling approach	158
The role of ambient and cryogenic pre-strain on hydrogen embrittlement of a FeNiCoCr high-entropy alloy: A comparative study	157
Formation and dissolution of porous magnetite layer in contact with lead-bismuth eutectic: Locally equilibrium thermodynamic model	154
Insights into the effect of Cr on interfacial and grain boundaries oxidation in Fe-Mn-Si-based alloys	143
Amount of hydrogen absorbed into 316L austenitic stainless steel and its correlation with properties of oxide film, dissolved oxygen concentration and low-cycle fatigue behaviors of this material in b	135
Controllable defect engineering to enhance the corrosion resistance of Cr/GLC multilayered coating for deep-sea applications	135
Al-modified environmental barrier coatings for protection against water vapor corrosion	129
Atomic-scale insight on nanostructures and electrochemical properties of (NiCrCo)82Ti9Al9 high-entropy alloy coatings by density functional theory calculations	129
Parameters to estimate the metal dusting attack in different gases	110
Corrigendum to “Microstructure response and lead-bismuth eutectic corrosion behavior of 11Cr1Si ferritic/martensitic steel after Au-ion irradiation” [Corros. Sci. 198 (2022) 110101]	110
Effect of surface hemispherical dent depth on the microstructure evolution and stress corrosion cracking of heat transfer tubes in steam generator	109
Chromium segregation-induced oxide evolution in Ni-10Cr alloys during high-temperature oxidation	107
Corrigendum to “Processable poly(2-butylaniline)hexagonal boron nitride nanohybrids for synergetic anticorrosive reinforcement of epoxy coating” [Corros. Sci. 131 (2018) 187–198]	106
Improving the resistance of exfoliation corrosion and stress corrosion cracking for high-strength aluminum alloy via tailored nanoparticles	104
The influence of aging temperature on microstructure and intergranular corrosion of Al-Mg-Si alloys with low concentrations of Cu and Zn	101
Enhancement of high-temperature oxidation resistance of the AgCu-based alloy by in-situ fabricating three-dimensional TiC nanosheet reinforcement	101
Oxidation of Zircaloy-4 under simulated accident conditions – kinetics and microstructural developments	101
Enhancing stress corrosion cracking resistance of high-strength bolt steels through Cu and Nb microalloying	99
Indirect interactions between the ionic liquid and Cu surface in 0.5 M HCl: a novel mechanism explaining cathodic corrosion inhibition	95
Understanding the mechanism of shrinkage defects on corrosion kinetics of ductile iron	95
Microstructural evolution of intermetallic phase precipitates in Cr-coated Zirconium alloy cladding in high-temperature steam oxidation up to 1400 °C	95

Influence of steam flow rate on oxidation kinetics of silicon carbide at 1400–1600 °C	94
Effect of temperature on the passive film structure and corrosion performance of CoCrFeMoNi high-entropy alloy	93
Near-atomic-scale study of the oxide films on the grain boundaries of Al-Mg alloys at the initial stage of corrosion: Experimental investigations and DFT calculations	93
In-situ rolling friction stir welding of aluminum alloys towards corrosion resistance	92
Electron microscopy analysis of grain boundaries and intergranular corrosion in aged Al-Mg-Si alloy doped with 0.05 wt% Cu	91
Fungi corrosion of high-strength aluminum alloys with different microstructures caused by marine Aspergillus terreus under seawater drop	90
Exploring the hydrogen embrittlement behavior in nickel-economized austenitic stainless steel: Investigating the role of manganese in modifying hydrogen-induced crack mechanisms	89
EIS interpretation on the structure evolution of passive coating on tinplate exposed to atmospheric environment	89
A multiple synergistic composite coating with ultrahigh anti-corrosion performance under harsh oxygen environment	87
Observation of the formation of CuAl2O4 by the direct consumption of Al2O3 in an NAB alloy at elevated temperature	87
Corrosion inhibition of aluminium alloys by molybdate ions: A critical review of the chemistry, mechanisms and applications	84
Salinity effect on corrosion inhibition of 2-mercaptopyrimidine as an inhibitor in CO2-containing solution	84
Microbiologically influenced corrosion of CoCrFeMnNi high entropy alloy by sulfate-reducing bacterium Desulfovibrio vulgaris	83
Enhancing the erosion–corrosion resistance of cupronickel alloy through grain boundary engineering	82
Effect of nitrogen on high temperature oxidation behavior of AlN-doped gradient coating	82
Study on the galvanic corrosion of titanium and stainless steel couple with the synergistic effect of proton and fluoride ion	81
Sm-composition engineering of (Hf, Zr, Ta, Sm)B2 high-entropy diborides for superior oxidation resistance	81
Effect of grain boundary on the ignition and flame propagation mechanisms of TC11 alloy in oxygen-enriched environment	80
Nanoindentation study of the oxide scale on FeCr alloy by high-pressure torsion	80
Role of cementite morphology on corrosion layer formation of high-strength carbon steels in sweet and sour environments	79
Effect of tensile stress on the corrosion morphology and multifractal characteristics of DH36 steel in a neutral salt spray environment	79
Improvement of carbon dots corrosion inhibition by ionic liquid modification: Experimental and computational investigations	77
Corrosion performance of the biocompatible β-Ti12Mo6Zr2Fe alloy submitted to laser and plasma-nitriding surface modifications	77
Effect of pre-treatment temperatures on the oxidation behaviors and surface roughening mechanisms of NiCoCrAlYHf coating	77
Improvement of steam oxidation resistance of the γ-TiAl alloy with microarc oxidation coatings at 900–1200 ℃	77
Extremely improved the corrosion resistance and anti-wear behavior of aluminum alloy in 3.5% NaCl solution via amorphous CrAlN coating protection	77
Corrosion mechanisms of 316L stainless steel in polyphosphoric acid at elevated temperature: Behavior and mechanistic insights	77
New insights from crystallography into the effect of boundaries on hydrogen embrittlement susceptibility of a 1000 MPa grade heavy gauge high-strength low-alloy steel	76
The impact of alloying elements on the irradiation and hydrogen-induced corrosion of the austenite in nuclear stainless steel	75
The effect of surface grinding and Si addition on the corrosion of Fe-12Cr ODS steels in supercritical CO2	74
Transpassivation-induced structural evolution of oxide film on 654SMO super austenitic stainless steel	74
Model for corrosion of copper in a nuclear waste repository	74
Significant improvement of corrosion resistance in laser cladded Zr-based metallic glass matrix composite coatings by laser remelting	74
New insights in the oxidation behavior of (FeCoCrNi)94Al4Ti2Si high entropy alloys at 1100 °C	74
Experimental approach and assessment of Zr conversion coatings on Al alloy using response surface methodology	73
A high-resolution study of the different surface state effects on the corrosion behaviors of a ferritic steel and an austenitic steel in supercritical water	73
Initial dissolution of Mg-containing phase and corrosion product formation in cut-edge corrosion of Zn-11%Al-3%Mg-0.2%Si coated steel	73
Study on the structure and corrosion behavior of hot-dipped Zn–6Al–3Mg alloy coating in chlorine-containing environment	72
Introduction of Cu2+ to the inside of the crevice by chelation and its effect on crevice corrosion of Type 316L stainless steel	71
Corrosion evolution and stress corrosion cracking behavior of a low carbon bainite steel in the marine environments: Effect of the marine zones	71
Selective adsorption and corrosion mechanism of SO2 and its hydrates on X65 welded joints steel in CO2-saturated aqueous solution	71
Corrosion behavior of AA6016/SM490 galvanic couple in NaCl-containing droplets: Effect of Fe species on galvanic corrosion acceleration	71
A novel (Ho0.2Er0.2Tm0.2Yb0.2Lu0.2)2Zr2O7 high-entropy ceramic with excellent CMAS corrosion resistance for thermal barrier coatings	71
The effect of zinc addition on corrosion behavior of stainless steels with different phases in simulated PWR primary water	70
Formation of protective conversion coating on Mg surface by inorganic inhibitor	69