OOIR: Observatory of International Research

Papers

(The TQCC of Cryogenics is 5. The table below lists those papers that are above that threshold based on CrossRef citation counts [max. 250 papers]. The publications cover those that have been published in the past four years, i.e., from 2020-05-01 to 2024-05-01.)

Article	Citations
Properties of cryogenic and low temperature composite materials – A review	70
Non-twisted stacks of coated conductors for magnets: Analysis of inductance and AC losses	43
Hydrogen liquefaction process with Brayton refrigeration cycle to utilize the cold energy of LNG	31
3D finite element modelling on racetrack coils using the homogeneous T-A formulation	22
Development of dilution refrigerators—A review	21
Performance metrics of electrical conductors for aerospace cryogenic motors, generators, and transmission cables	18
Elasticity, plasticity and fracture toughness at ambient and cryogenic temperatures of epoxy systems used for the impregnation of high-field superconducting magnets	18
Influence of field-dependent critical current on harmonic AC loss analysis in HTS coils for superconducting transformers supplying non-linear loads	17
Experimental study on hydrogen pulsating heat pipes under different number of turns	17
Thermodynamic effects on the cavitation flow of a liquid oxygen turbopump	16
Temperature sensitivity analysis of inner-gate engineered JL-SiNT-FET: An Analog/RF prospective	16
The microstructures and mechanical properties of dissimilar laser welding of copper and 316L stainless steel with Ni interlayer	16
Numerical investigation of transient liquid nitrogen cavitating flows with special emphasis on force evolution and entropy features	15
Thermo-hydraulic and economic aspects of long-length high-power MgB2 superconducting cables	15
Development of fiber Bragg grating strain sensor with temperature compensation for measurement of cryogenic structures	15
Role of trivalent Bi/Tm partial substitution on active operable slip systems in Bi-2212 crystal structure	15
A novel integrated structure of hydrogen purification and liquefaction using natural gas steam reforming, organic Rankine cycle and photovoltaic panels	14
Structural and superconducting properties of low-density Bi(Pb)-2223 superconductor: Effect of Eu2O3 nanoparticles addition	13
Effect of frost layer on heat transfer of cryogenic fluid in a finned tube	13
General design of ±100 kV/1kA energy pipeline for electric power and LNG transportation	13
HTS transformers leakage flux and short circuit force mitigation through optimal design of auxiliary windings	13
Coaxial Stirling pulse tube cryocooler with active displacer	13
Internal and external flow characteristics of multi-nozzle spray with liquid nitrogen	12
Experimental analysis of thermal behavior in cryogenic propellant tank with different pressurants	12
Mechanical properties and microstructure evolution of cryogenic pre-strained 316LN stainless steel	12

Development of cryogenic cooler based on n-type Bi-Sb thermoelectric and HTSC	12
High-precision calibration for strain and temperature sensitivities of Rayleigh-scattering-based DOFS at cryogenic temperatures	12
Investigations on a 1 K hybrid cryocooler composed of a four-stage Stirling-type pulse tube cryocooler and a Joule-Thomson cooler. Part A: Theoretical analyses and modeling	11
A work-recovery pulse tube refrigerator for natural gas liquefaction	11
Simulation study on the cryogenic liquid nitrogen jets: Effects of equations of state and turbulence models	11
The end part of cryogenic H. V. bushing insulation design in a 230/20 kV HTS transformer	11
Numerical investigation on the flow characteristics of liquid oxygen and water in the structured packing	11
Magnetocaloric effect in LiLn6O5(BO3)3 (Ln = Gd, Tb, Dy, and Ho)	11
Cascade JT systems with single-component refrigerants for hydrogen liquefaction	11
Magnetothermal properties and magnetocaloric effect in transition Metal-Rich Gd-Co and Gd-Fe amorphous alloys	10
Cooling system for the Resolve onboard XRISM	10
Numerical investigation on serrated fin of sub-atmosphere plate-fin heat exchanger used in superfluid helium system	10
Investigation on leakage vortex cavitation and corresponding enstrophy characteristics in a liquid nitrogen inducer	10
Optimization of a Zigzag-channel printed circuit heat exchanger for supercritical methane flow	10
Numerical analysis of spray characteristics with liquid nitrogen	10
Simulation and experiment on superconducting DC energy pipeline cooled by LNG	10
Bending and uniaxial tensile strain effects on the critical current of REBCO coated conductor tapes	10
Dynamic performance of HTS maglev and comparisons with another two types of high-speed railway vehicles	10
Recent concept study for cryogenic fluid management to support opposition class crewed missions to Mars	10
Comparing the predictive ability of two- and three-parameter cubic equations of state in calculating specific heat capacity, Joule – Thomson coefficient, inversion curve and outlet temperature from Jo	10
Optimization of thermoelectric modules for maximum cooling capacity	10
Refractometric and temperature sensors based on one-dimensional binary photonic crystal including a superconducting layer	10
An analytical model for coupling losses in large conductors for magnetic fusion	9
Large eddy simulation based multi-environment PDF modelling for mixing processes of transcritical and supercritical cryogenic nitrogen jets	9
OLYMPE, a multi-physic platform for fusion magnet design: Development status and first applications	9
Experimental and numerical study on AC loss reduction in a REBCO coil assembly by applying high saturation field powder-core flux diverters	9
Numerical simulation of cryogenic cavitating flow in LRE oxygen turbopump inducer	9
Cryogenic treatment of an AISI D2 steel: The role of isothermal martensite formation and “martensite conditioning”	9
Numerical investigation on heat transfer and flow characteristics of supercritical methane in a horizontal tube	9
Compliant polymer origami bellows in cryogenics	9
Numerical investigation of a nitrogen based cryogenic pulsating heat pipe	8
Preliminary study on three-dimensional imaging of cryogenic two-phase flow based on electrical capacitance volume tomography	8
Cryogenic thermal conductivity of 7050 aluminum alloy subjected to different heat treatments	8
Linking trap to G10 surface flashover in liquid nitrogen under DC voltage	8
Cooldown of insulated metals in saturated and subcooled liquid nitrogen	8
Effects of stainless steel thickness and winding tension on electrical and thermal characteristics of metal insulation racetrack coils for 10-MW-class HTS wind generator	8
The daily evaporation rate test and conversion method for a new independent type B LNG mock-up tank	8
Analytical solutions for N interacting electron system confined in graph of coupled electrostatic semiconductor and superconducting quantum dots in tight-binding model	8
Numerical studies on unstable oscillatory direct contact condensation (DCC) of oxygen vapor jets in subcooled flowing liquid oxygen	8
Composition optimization method for mixed refrigerant MR JT cryocooler	8
Development of a compact 2.17 K hybrid 4He JT cryocooler for space applications	7
Lifetime test of the 4K Joule-Thomson cryocooler	7
Study on pressure wave propagation through cryogenic condensing two-phase flow in liquid rocket propellant feedline	7
Numerical investigation on the distribution characteristics of gas-liquid flow at the entrance of LNG plate-fin heat exchangers	7
Electromagnetic behaviour and thermal stability of a conduction-cooled, no-insulated 2G-HTS coil at intermediate temperatures	7
Effects of natural gas compositions on its Joule–Thomson coefficients and Joule–Thomson inversion curves	7
Mathematical modeling of thermal stratification in a double wall cryogenic propellant tank with different insulations using one-dimensional flow over vertical plate approximation	7
Design of a magnet to study quench propagation in a Cable-In-Conduit-Conductor filled with stagnant superfluid helium	7
An open hardware 3-D printed device for measuring tensile properties of thermoplastic filament polymers at cryogenic temperatures	7
High-speed density measurement for LNG and other cryogenic fluids using electrical capacitance tomography	7

Cooling system optimization of cryogenic propellant storage on lunar surface	7
Adsorption equilibrium and charge/discharge characteristics of hydrogen on MOFs	7
ATHENA X-IFU 300 K–50 mK cryochain test results	7
Magnetothermal properties and magnetocaloric effect in ErFe2	7
Measurements of self-field and voltage for the REBCO stacked tapes assembled in rigid structure (STARS) conductor at 77 K	6
Modeling and analysis of heat transfer in submerged combustion vaporizer under supercritical pressure	6
Experimental investigations on high pressure ratio cryogenic turboexpanders for helium liquefier	6
Effects of thallium fluoride and yttrium on structure, electrical properties and ac losses susceptibility of (Bi,Pb)-2234 superconductors	6
An efficient HTS electromagnetic model combining thin-strip, homogeneous and multi-scale methods by T-A formulation	6
Experimental imaging and algorithm optimization based on deep neural network for electrical capacitance tomography for LN2-VN2 flow	6
High performance thermal link with small spring constant for cryogenic applications	6
Heat transfer characteristics of liquid hydrogen flowing inside of a vertical heated pipe under quasi-stationary heat input	6
Numerical investigation of nitrogen condensation flow over airfoil in cryogenic wind tunnel	6
Experimental study on liquid oxygen chill-down in a horizontal exit-contracted pipe	6
Exergetic analysis of reverse Brayton cryocooler with different turbine arrangements for HTS power cables	6
Cooling performance of multi-nozzle spray with liquid nitrogen	6
Pool boiling in liquid hydrogen, liquid methane and liquid oxygen: A review of available data and predictive tools	6
Quench analysis of the DEMO CS1 coil	6
Numerical study on natural convection of liquid nitrogen used to cool the high-temperature superconducting cable in a new combined energy transmission system	6
Experimental study on a hydrogen pulsating heat pipe in different heating modes	6
Numerical study on a three-stage traveling-wave thermoacoustic generator with a simplified structure simultaneously utilizing cold and low-grade thermal energy	6
Numerical study on two-phase expansion performance and quantitative analysis of wetness loss in cryogenic turbo-expander	6
Impact of Ti-doping position on Nb3Sn layer formation in internal Sn-processed Nb3Sn superconducting wires	6
10 kV AC test verification of the high temperature superconducting fault current limiter with bias magnetic field	6
Numerical analysis of cryogenic LOX-LN2 mass transfer characteristics under different textured surfaces	6
Appropriate number of stages of an ORC driven by LNG cold energy to produce acceptable power with reasonable surface area of heat exchangers	6
Influence of gas axial conduction enhancement factor on the oscillating flow behavior of an inertance pulse tube cryocooler	6
The effect of flux diverters on the AC loss of REBCO coil coupled with iron core	6
2 K cryogenic system development for superconducting cavity testing of CiADS	6
Experimental investigation of cryogenic flow quenching of horizontal stainless steel tubes	6
Calculation of radial force of radial HTS magnetic bearing	6
Investigation on the thermal performance of spiral wound heat exchanger for the superfluid helium cryogenic system	6
Investigations on a 1 K hybrid cryocooler composed of a four-stage Stirling-type pulse tube cryocooler and a Joule-Thomson cooler. Part B: Experimental verifications	6
Collision dynamics of two liquid nitrogen droplets under a low-temperature condition	6
Prediction of Joule–Thomson coefficients and inversion curves of natural gas by various equations of state	6
An innovative integrated process for helium and NGL recovery and nitrogen removal	6
Development of switchless thin-plate type sorption compressor cell for 5 K sorption J-T refrigerator	6
Application of machine learning techniques in operating parameters prediction of Stirling cryocooler	6
Thermal characteristics of a helium-free superconducting magnet system for a fast-ramping heavy-ion synchrotron	6
Geometrical modeling and mechanical behavior analysis of Nb3Sn Rutherford cable	6
Determining design criteria to reduce power and cost in filling high-pressure oxygen cylinders directly from cryogenic air separation plants	6
Numerical investigation on the direct contact condensation of oxygen jets in a cryogenic pipe	6
Transient performance study of high pressure fuel gas supply system for LNG fueled ships	5
AC susceptibility and electrical properties of Ta substituted (Tl1Ta )(BaSr)CaCu2O7 superconductor (x = 0–0.3)	5
Numerical simulation on heat transfer and flow of supercritical methane in printed circuit heat exchangers	5
Modeling and characteristics investigation of self-regulating HTS flux pump	5
Superconducting and levitation force characterisation of pyrene added MgB2 bulk superconductors	5
Elimination of δ-ferrite in N50 steel and its effect on cryogenic mechanical properties	5
Role of Supercritical Nitrogen (SCN) on the hydraulic and thermal characteristics of futuristic High Temperature Superconducting (HTS) cables	5
Numerical analysis of the mechanical and electrical properties of CORC cables under torsional loading	5
Profitability of low-temperature power electronics and potential applications	5
Effects of bending and torsion behavior on Ic degradation and microstructure of ReBCO coated conductors	5
Frozen image analysis of a superconducting magnetic levitation system consisting of multi-surface superconductor and Halbach array permanent magnet configuration	5
Thermal-hydraulic analysis of superconducting cables for energy applications with a novel open object-oriented software: OPENSC2	5
Development of CFD model for the analysis of a cryogenics twin-screw hydrogen extruder system	5
Assessment of prediction and efficiency parameters for cryogenic no-vent fill	5
AC breakdown channel of PPLP multi-layer insulation for HTS cable	5
Thermal analysis and experimental study of cryostat for superconducting wiggler of the HEPS-TF	5
Novel condenser based cryogenic pulsating heat Pipe: Investigations on influence of geometrical parameters	5
Mechanical design of the magnet mirror structure for testing Nb3Sn sextupole coil of 45 GHz ECRIS	5
Characterization of a Si and GaN converter at cryogenic temperatures	5
Numerical simulation of a low temperature hybrid refrigerator combining GM gas expansion refrigeration with magnetic refrigeration	5
Experimental system for testing a superconducting motor at temperatures close to 15 K	5
Exergoeconomic assessment of air separation units for pressurized O2 production incorporating two-phase expanders	5
Gas-gap heat switches with negative room temperature conductor separation and their application to ultra-low temperature platforms	5
The long duration cryogenic system of the OLIMPO balloon–borne experiment: Design and in–flight performance	5
Design evaluation of serial and parallel sub-mK continuous nuclear demagnetization refrigerators	5
Optimization and experiment on the dual nitrogen expansion liquefaction process with pre-cooling	5
Effect of Sb-doped YBa2-xSbxCu3O7-δ superconductor on electronic behaviour using density functional theory	5
Methane liquefaction with an active magnetic regenerative refrigerator	5
Liquid hydrogen pipeline chill-down: Mathematical modelling and investigation	5
Study on the electrical performances of soldered joints between HTS coated-conductors	5