OOIR: Observatory of International Research

Papers

(The TQCC of Experimental Mechanics is 6. The table below lists those papers that are above that threshold based on CrossRef citation counts [max. 250 papers]. The publications cover those that have been published in the past four years, i.e., from 2022-05-01 to 2026-05-01.)

Article	Citations
Dynamic Magneto-Mechanical Analysis of Isotropic and Anisotropic Magneto-Active Elastomers	39
Editorial: Message from the Incoming Editor-in-Chief	35
Asynchronous Identification for Time-Dependent Materials	32
Experimental Characterization and Numerical Modelling of the Impact Behavior of PVC Foams	31
Synchronous Raman Spectroscopy Method for Measuring Strain-Charge Information of Graphene Materials	26
Compressive Properties of Aluminium Foam-Filled Square Stainless Steel Tubes With Elliptical and Circular Holes	24
Correction: Assessment and Validation of Incremental Hole-Drilling Calculation Methods for Residual Stress Determination in Fiber-Metal Laminates	22
Correction: A Comparative Study of the Performance of IR Detectors vs. High-Speed Cameras Under Dynamic Loading Conditions	21
High-Speed, 3D Volumetric Displacement and Strain Mapping in Soft Materials Using Light Field Microscopy	20
4D Porosity Evolution in Additively Manufactured 316L Stainless Steel through In-Situ Tensile Testing and X-Ray Computed Tomography	19
Quantitative Full-Field Data Fusion for Evaluation of Complex Structures	19
On the Cover: Unique Identification of Stiffness Parameters in Hyperelastic Models for Anisotropic, Deformable, Thin Materials Based on a Single Experiment - A Feasibility Study Based on Virtual Full-	18
Rapid Determination of Fatigue Limit Using Temperature Second Harmonic	18
Designing Patterns for DIC with Poisson Image Editing	18
Ill-Posedness and the Bias-Variance Tradeoff in Residual Stress Measurement Inverse Solutions	18
Mechanical Characterisation and Simulation of the Tensile Behaviour of Polymeric Additively Manufactured Lattice Structures	17
2D and 3D Characterization of Damage Mechanisms in A319 Alloy	17
Thermoelastic Stress Measurement Using SVD Thermo-Component Analysis	17
On Detecting Elastoplastic Shakedown Using Minimal Digital Image Correlation Results and an Elastic Model: Demonstration for AA6061 Auxetic Sheets	17
Data-Driven Accelerated Parameter Identification for Chaboche-Type Visco-Plastic Material Models to Describe the Relaxation Behavior of Copper Alloys	16
A Note On Measuring Mechanical Fields in 3-D Solids Using Digital Gradient Sensing and Refractive Index Matching	16
Design, Preparation and Dynamic Response of a Composite Magnetorheological Elastomer-Based Intelligent Dynamic Vibration Absorber	15
Hole-Drilling Method for Deep Residual Stress Measure in Tensile Armour Wires	14
Comparison Study of Three Camera Calibration Methods Considering the Calibration Board Quality and 3D Measurement Accuracy	14
An INNOVative Approach for Mechanical Characterization of Coatings on Fibres	13

Analysis and Comparison of the Projectile Impact Response of an Electron Beam Melt-Ti64 Body Centered Cubic Lattice-Cored Sandwich Plate	13
Improvement in Calibration Procedure in Nanoindentation: An Indenter Bluntness Indicator	13
The Role of Buckling Instabilities in the Global and Local Mechanical Response in Porous Collagen Scaffolds	13
Thermal Stress Analysis for Functionally Graded Plates with Modulus Gradation, Part II	13
Exploring Humerus Bone’s Fracture Patterns and Fixation Systems Via Laser Vibrometry	12
A Visible-UV DIC Technique for Full-Field Reconstruction of Multi-Layer Tensioned Membrane Systems	12
Uncoupling the Effects of High Strain Rate and Adiabatic Heating on Strain Induced Martensitic Phase Transformations in a Metastable Austenitic Steel	12
Digital Image Correlation Under Large Rotations or Off-Axis: An APT-DIC Method with SURF-Driven Affine-Projective	12
Quantification of Reinforcement Debonding in Damaged Mortar via Digital Volume Correlation	12
Influence of the Experimental Setup on the Damping Properties of SLM Lattice Structures	12
On the Cover: Operando Characterizations of Lithium Penetration-Induced Fracture in Solid Electrolytes by M. Lu, S. Xia	11
Fine-Tuning a Deconvolution Algorithm to Restore Displacement and Strain Maps Obtained with LSA	11
A Novel MEMS Platform for Thermomechanical Characterization of Nanomaterials	11
Full-Field Digital Photoelastic Quantification of Principal Stress Difference Under Continuous Loading	11
Subsurface and Bulk Residual Stress Analysis of S235JRC + C Steel TIG Weld by Diffraction and Magnetic Stray Field Measurements	11
Full-Field Measurement of Dynamic Shear Ruptures Using Digital Gradient Sensing	11
The Estimation of Taylor-Quinney Coefficients Using Small Ring Specimens	11
Microstructure Informed Mechanical Properties and Chemomechanical Degradation of Battery Cathode Particles	11
Simulation and Experimental Validation of the Cure Process of an Epoxy-Based Encapsulant	11
Numerical Modelling of an Aneurysm Mechanical Characterisation Device: Validation Procedure Based on FEA-DIC Comparisons	11
A Robot-Assisted Microscopy System for Digital Image Correlation in Fatigue Crack Growth Testing	11
A Strain Field Reconstruction Method Based on Digital Twin by Multi-Level Fusion of Multi-Type Data	11
Tikhonov Regularization for the Fully Coupled Integral Method of Incremental Hole-Drilling	10
Novel Speckle Preparation and Heat Insulation Method for DIC Strain Measurement at Cryogenic Temperature and Large Deformation Environment	10
Measurement of Contact Force–Deformation Curves of Colliding Two Identical Spheres	10
Fatigue Damage Evolution in SS316L Produced by Powder Bed Fusion in Different Orientations with Reused Powder Feedstock	10
Investigating Speed and Temperature Effects on Puncture of Elastomers	10
High-Speed, Full-Field Deformation Measurements Near Inertial Microcavitation Bubbles Inside Viscoelastic Hydrogels	10
Debonding Analysis of Fibre Reinforced Polymer Anchors in Concrete via In-Situ X-Ray Microtomography Tests Coupled to Volume and Digital Image Correlation	10
Strain Determination Using a Global Interpolation Concept Based on Coherence Scanning Interferometry Measurements	9
Study on the Characteristics of Shock Wave Propagation in Explosively Driven Shock Tubes	9
Load Capacity of Concave Conical Shells with Randomly Positioned Circular Cutouts	9
Ultraviolet Single-Camera Stereo-Digital Image Correlation for Deformation Measurement up to 2600 °C	9
On the Cover: Introducing Virtual DIC to Remove Interpolation Bias and Process Optimal Patterns	9
Necking-Shaped Shear Experiment for Measuring the Interlayer Shear Strengths of 3D Printed Titanium Alloys	9
Evaluation of Wave Velocity in Orthotropic Media Based on Intrinsic Transfer Matrix	9
Performing Stereo-Measurements with Optimal Patterns Processed by Localised Spectrum Analysis	9
The SFIR Test: An Innovative Hydrostatic Compression Test to Characterize the Volumetric Behavior of Polymeric Foams	9
Experimental Study on Dynamic Mechanical Behavior of Fully-Penetrating Cross-Jointed Rocks Under Biaxial Static-Dynamic Loading	9
Introducing Virtual DIC to Remove Interpolation Bias and Process Optimal Patterns	9
Development of a P‒T-Model-Based In-Situ Bending Measurement Method for Nanowires: Addressing Mechanical Challenges in High-Precision Experiments	9
Quantification of Errors in Applying DIC to Fiber Networks Imaged by Confocal Microscopy	9
Experiments on Low–Cycle Ductile Damage and Failure Under Biaxial Loading Conditions	9
Experimental Investigation of the Ballistic Response of Head Surrogate Against Fragment Simulating Projectiles	9
Biomechanical Hand Model: Modeling and Simulating the Lateral Pinch Movement	9
A Modified Losipescu Method for Evaluating In-Situ Shear Behavior Using High-Temperature X-Ray Computed Tomography	9
In-Situ Characterization on Fracture Toughness of Thermal Barrier Coatings Under Tension by J-Integral with Digital Image Correlation at High Temperatures	8
An Improved Strain Field Reconstruction Method Based on Digital Twin for Test Monitoring	8
Incremental FIB-DIC Ring-Core Methods for the Residual Stress Measurement of Bilayer Thin Films	8
Celebrating Prof. Cesar Sciammarella’s 100th Anniversary and Contributions	8

Sensitivity Study Using Synthetic 3D Image Datasets to Investigate the Effect of Noise Artefacts on Digital Volume Correlation	8
Friction Characteristics of Two-Dimensional Hybrid Organic-Inorganic Perovskites	8
Chromatic Aberration Compensation of a Lens for Use in Any CCD Camera	8
A Method to Perform an Experimental Modal Analysis of a Medium Head Francis Runner in Operation	8
Shape Measurements of Lattice Materials from Few X-Ray Radiographs Using the 3D Virtual Image Correlation (3D-VIC) Method	8
Crack Growth of Defects in Ti-6Al-4V Under Uniaxial Tension: Measurements and Modeling	8
Layer Jamming of Magnetorheological Elastomers for Variable Stiffness in Soft Robots	8
On the Cover: Design and Validation of a Symmetric Drop Weight System for Tensile Intermediate Strain Rate Characterization	8
Opening-Dominated Fracture Characterization of Single Crystal Spinel in the Transmission Electron Microscope	8
High Accurate Stereo-Digital Image Correlation Method in Liquid Nitrogen Immersion Conditions with Single Camera	8
Predicting Camera Sensor Noise Propagation to Displacement and Strain Maps Retrieved from Checkerboard Patterns with Localized Spectrum Analysis	8
A Novel High-Speed Bulge Test to Identify the Large Deformation Behavior of Sheet Metals	8
On the Cover: Characterization and Prediction of Polymer/Active Material Interface Failure in Battery Electrodes	7
Post-Yield Compression Characterization of Epon 828/DEA Epoxy	7
Silicon-Based Microscale Multistable Metamaterials: Microfabrication and Characterization	7
Biaxial Extension of Cruciform Specimens: Embedding Equilibrium Into Design and Constitutive Characterization	7
Optimization on Cruciform Specimen Geometries of AA5052 Under Equi-Biaxial Loading: Acquisition of Ultimate Fracture Strain	7
Effect of Solution Methods for Evolutionary R-Values on the Prediction of Anisotropic Yield Behavior	7
Research on Strain Modulation of Spectral Reflectance in Soft Materials	7
Stress-Based S–N Base Function with Shear Modulus for Fatigue Assessment on Industrial Isolators	7
On the Cover: 2020 Murray Lecture: Quantitative Full Field Data Fusion for Evaluation of Complex Structures	7
On the Hyperelastic Behavior of the Boar Diaphragmatic Tendon Membrane by Inflation Tests and Modeling	7
Thermoelastic Stress Analysis in the Presence of Biaxial Stresses in Titanium: Effect of the Mean Stress on Errors in Stress Evaluation	7
Core Collapse Instability of Spirally Wound Jelly-Roll Lithium-Ion Batteries	7
On the Cover: Exploring Humerus Bone’s Fracture Patterns and Fixation Systems Via Laser Vibrometry	7
Thermal Expansion Coefficient Measurement of Stack Structure of REBCO Coated Conductors By Strain Gages At Cryogenic Temperatures	7
Comparison of Hall–Petch Law with an Elastic Limit Identification Method Using Kinematic Field Measurements	7
Improving Deep Learning‑Based Digital Image Correlation with Zero Mean Normalized Cross-Correlation	7
Correction: Experimental Investigation of the Ballistic Response of Head Surrogate Against Fragment Simulating Projectiles	7
Application of Hyperspectral Imaging Technique and Artificial Intelligence on Quality Prediction of Embryonic Cells	6
Ballistic and Blast-Relevant, High-Rate Material Properties of Physically and Chemically Crosslinked Hydrogels	6
On the Cover: High Speed Impact Testing of UHMWPE Composite Using Orthogonal Arrays	6
Image-Based Deformation Measurement of Aerodynamic Heating Surfaces Using Time-Gated Active Imaging Digital Image Correlation	6
Mechanical Fatigue Testing Under Thermal Gradient and Manufacturing Variabilities in Nickel-Based Superalloy Parts with Air-Cooling Holes	6
Experimental Investigation of Shear Behavior in 3D Woven Carbon/Carbon Composites Under Static and Dynamic Loading	6
A Photoacoustic Method to Measure the Young’s Modulus of Plant Tissues	6
Estimation of Fatigue Limit for Aluminum Alloy Laser Welds Based on Dissipated Energy	6
On the Cover: Investigation of Mechanical Behavior of Water-Imbibed Polymeric Foams Under Dynamic Shear-Compression Loading for Tribology Application	6
An Accurate Strain Gauge Positioning Approach Based on Geometry and Color Features	6
Creep Characterization of Amorphous SiO2 in the Transmission Electron Microscope Using Digital Image Correlation and Finite Element Analysis	6
Hinged Rigid Beam Fracture Specimen for Characterization of Lattice and Thin-Sheet Materials	6
Damage Tolerance Assessment of Laser Clad Repairs of Coarse Grain Ti-6Al-4V	6
An Improved Test Procedure for Mechanical Characterization of Flax-Epoxy Composites	6
Stereo-DIC Challenge 1.0 – Rigid Body Motion of a Complex Shape	6
Guided Ultrasound Inspection of Small Features Using a Horn-Type Transducer Design	6
On the Cover: Designing Patterns for DIC with Poisson Image Editing	6
Dynamic Compressive Test of Saturated Sandstones Under Ambient Sub-Zero Temperature	6
Triaxial Characterization of Foams at High Strain Rate Using Split-Hopkinson Pressure Bar	6
Measurement of Nonuniform Strain Distribution in CORC Cable Due to Bending Process by a Segmentation-Aided Stereo Digital Image Correlation	6