Transactions of the Institute of Metal Finishing

Papers
(The TQCC of Transactions of the Institute of Metal Finishing is 2. The table below lists those papers that are above that threshold based on CrossRef citation counts [max. 250 papers]. The publications cover those that have been published in the past four years, i.e., from 2021-04-01 to 2025-04-01.)
ArticleCitations
Corrosion protection behaviour of electrogalvanised steel sheet by tetravalent vanadium ion53
Hydroxyapatite formation of Ca and P modified micro-arc oxidation coating on Ti alloy33
Some structural aspects and future challenges for the global surface finishing industry21
Prizes and grants from European Academy of Surface Technology18
The effect of plasma electrolytic oxidation coatings from aluminate electrolyte processing systems on the fretting wear performance of TC4 alloy15
Novel silver-enhanced hard gold electrodeposit applied for electrical contacts: comparison with conventional gold–cobalt alloy12
Subject Index11
Surface morphology of silver thin films exposed to water vapour and/or oxygen in vacuum9
Influence of picoseconds laser irradiation on the properties of black chromium obtained in a trivalent chromium bath8
Kinetic study of boron diffusion in a γ-TiAl intermetallic alloy using the pack-boronising method8
Is our industry up to speed with new technology?8
Effect of hydrogen embrittlement on the tribo-mechanical properties of TiN coated aluminium alloys7
Study on pin temperature and wear behaviour of plasma sprayed Ni-Cr coatings with nano Al 2 O 3 particle7
Dr Lars Pleth Nielsen (December 1968 - 23 May 2024)7
Tribological performance of thermally sprayed NiWCrBSi alloy coating by two different oxyacetylene flame stoichiometries6
Effect of incorporation of graphite nanoparticles on wear characteristics of Mg-WC nano-composites in dry sliding condition6
Modification of the surface of ABS polymer by swelling operation and its influence on some properties of electroless deposited metal coatings6
Producing a thin coloured film on stainless steels – a review. Part 2: non-electrochemical and laser processes6
Hydroxyapatite nanoparticles coating on Ti-6Al-4V substrate using plasma spray method6
Comparative study on machining performance of TiAlSiN, AlTiN/TiAlSiN-coated cutting tools6
A comprehensive review of vapour deposited coatings for cutting tools: properties and recent advances6
Biofilms formed on metallic materials by E. coli and S. epidermidis and their evaluation by crystal violet staining and its reflection5
Recent advances and challenges associated with thin film coatings of cutting tools: a critical review5
Typical metal implant materials and the application of laser cladding in their surface modification5
Electrochemical machining post-processing of additively manufactured nickel-based superalloys via laser directed energy deposition5
Effect of etching conditions on electroless Ni-P plating of 3D printed polylactic acid4
Characterisation, hardness and corrosion behaviour of electrodeposited ZnFe and ZnFe/BN composite coatings4
Effect of sodium dodecyl sulphate on Cu electrodeposition: interaction with hydrophobic substrate and Cu ions4
Selection of a suitable environmentally friendly (non-toxic) etching solution in the electroless metallisation of ABS polymers4
Investigation of Al-doped CuO thin film deposition by the thermionic vacuum arc technique4
Optimisation of a Ce–Mn co-doped SnO2–Sb anode based on a nanotubular TiO2 array for electrochemical decolourisation of wastewater4
15th EDNANO (International Workshop on Electrodeposited Nanostructures) integrating EAST Forum 20234
Dr JPG Farr FIMF (1931–2023)3
Dr. Joe Edwards FIMF (1925–2021)3
Effect on wear properties of coating the surface of 904L super austenitic stainless steel by APS with white/grey Al2O33
Subject Index3
Editorial3
Enhancing wear resistance of AISI 304 alloy with shot peening and investigation of corrosion behaviour in marine water3
Corrosion behaviour of Zn-Co alloy and multilayered metallic coatings: a comparative insight3
New key persons when research institute on precious metals turns 100 years old3
Antibacterial activity and biocompatibility of Ag-coated Ti implants: importance of surface modification parameters3
Co-deposited CuNi@MWCNTs nanocomposites for structural applications: tribo-mechanical and anti-corrosion performances3
CF Ipal – a case study of the chrome-free drop in replacement for IP1041 hexavalent chrome coating3
Estimation of indenter depth during frictional treatment of nickel-based coatings using optical profilometry3
Study of mechanical properties and biocompatibility of tantalum-containing coatings on NiTi orthodontic archwires3
Transactions of the Institute of Materials Finishing 2022, volume 100Author Index2
Multi-scan cyclic voltammetry to roughen the surface of copper foil for application in copper-clad laminates2
Thermal oxidation of Ni – 40 wt.% W and Ni – 50 wt.% W coated copper2
Development of an environmentally friendly pre-treatment for electroless metallisation of glasses2
Preparation of nanoporous copper foil by chemical dealloying from electro-deposited CuZn alloy2
Characteristics and corrosion resistance of hard-anodised 6061-T6 aluminium alloy2
Annual Contents 20222
Subject Index2
High entropy alloy (HEA) electrodeposits: importance, properties and uses2
Surface characteristics of plasma electrolytic oxidation coatings on Cp-Ti and hot-dip aluminised Cp-Ti2
Surface modification of ABS polymer by electroless deposition of thin nickel film from a solution without reducing agent2
Interfinish 2024: 21st World Congress of the IUSF2
IMF qualification modules2
Editorial2
Machine learning prediction of microhardness and corrosion current density of Ni-Co alloys produced by scanning jet electrodeposition2
Editorial2
Effect of nitriding nitrogen pressure on the structural, morphological, mechanical and tribological properties of plasma nitrided hard chromium electroplated layer2
0.059509038925171