OOIR: Observatory of International Research

Papers

(The H4-Index of International Journal of Mechanical Sciences is 76. The table below lists those papers that are above that threshold based on CrossRef citation counts [max. 250 papers]. The publications cover those that have been published in the past four years, i.e., from 2022-05-01 to 2026-05-01.)

Article	Citations
Uncertainty quantification for structural response field with ultra-high dimensions	345
Flat indentation on one-dimensional quasicrystal laminates with imperfect interfaces	215
Transverse forced vibration of a diamond wire under support excitations	212
Peridynamic mesh-free simulation of glass and metal beads column collapses	200
Smart helical swimmer: Nested and uncoiled designs	187
A viscoelastic-viscoplastic thermo-mechanical model for polymers under hypervelocity impact	177
Shock compression of nanoporous silicon carbide at high strain rate	155
Sensitivity-aided active control of flow past twin cylinders	143
Analytical optimization of rate-independent negative stiffness dampers for vibration control	143
Fatigue damage tolerance of CFRP/Al adhesive joints with thermal effects	138
Wave propagation in periodic nano structures through second strain gradient elasticity	135
Effect of grain boundary on scratch behavior of polycrystalline copper	133
Efficient dataset generation for inverse design of micro-perforated sonic crystals	132
Enhanced mechanical properties of spider web-inspired re-entrant honeycombs	126
Quantification, localization, and reconstruction of impact force on interval composite structures	125
Analytic vibration solutions for moving-loaded composite plates beyond Lévy boundaries	124
An ultra-precision running-in chemical mechanical polishing method for bearing rollers	124
Editorial Board	124
Editorial Board	123
Editorial Board	119
Editorial Board	116
Electro-mechanical-acoustic coupled dynamic modeling and experimental validation of acoustic tweezer	115
Power screw-assisted reconfigurable reflective metasurface with spatial modulation	115
Numerical cross-scale optimization of homogenized composite laminates under impact loading	114
Closed-form solutions for wave propagation in hexagonal diatomic non-local lattices	113

Bistable property and energy programming of lanyard coilable masts inspired by Kresling origami	113
Self-rolling and circling of a conical liquid crystal elastomer rod on a hot surface	112
Compressive-sensing model reconstruction of nonlinear systems with multiple attractors	111
A time domain procedure for the identification of periodic structures	109
Modeling of quasi-2D experiments on fine-scale dual-phase steel deformation mechanisms	109
Corrosion-induced mechanical degradation of SiCp/Al: Experimental and numerical analysis	109
Rigid spheroid migration in square channel flow of power-law fluids	108
Buckling behavior of soft spherical shells with patterned surface under indentation	107
WITHDRAWN: Recent advances in modeling and simulation approaches for fiber/matrix interface failure in FRP composites	107
Three-dimensional thermal-stress analysis of transversely isotropic double-layer plate based on Green's function	105
Dispersion properties of guided elastic waves in micropolar plates	104
Relative sensitivity of nano-mechanical cantilevers to stiffness and mass variation	101
A detachable chain tensile energy absorber inspired by mortise and tenon joint	99
A multimesh finite element method for integral nonlocal elasticity using mesh-decoupling technique	99
Tunable pure shear deformation of voltage/charge loaded dielectric elastomers	99
Numerical investigations on the viscoelastic-damage behaviors of RIVE-induced concrete	99
A coupled thermal-mechanical-oxidative model for predicting oxidation and stress affected by cracks	98
Levitation force enhancing and vibration reducing of NFAL via air-film compensation	97
Acoustic metamaterial lens for two-dimensional vortex beamforming and perception	96
A new performance indicator for heterogeneous elastoplastic material test specimens	95
Atomistic study of radiation-induced ductile-to-brittle transition in austenitic steel	94
Enhancement of thermo-fluid performance of square cylinder by dual splitter plates	93
Stiffness characteristics for bi-directional tunable thermal expansion metamaterial based on bi-material triangular unit	93
Modal analysis and multidisciplinary optimization of disk-shaped rotor in MSCMG	93
A genus-tuning design on minimal surfaces for open-cell mechanical metamaterials	89
Vacancy dependent shock response of high-entropy alloy FeNiCrCoCu	88
Dynamic reliability analysis of main shaft bearings in wind turbines	88
Transfer learning-based crashworthiness prediction for the composite structure of a subway vehicle	87
Size effects and the existence of scalable materials and systems	87
Vibration isolation performance and optimization design of a tuned inerter negative stiffness damper	86
Nanoscale deformation and removal mechanisms in Al/SiC composites	86
Mechanistic and data-driven modeling of diaphragm coupling misalignment dynamics	85
Analytical solutions for film stress and bending deformation of coated optical lenses	85
Needling model for predicting mechanical behaviours of waste cotton composites	85
Shell vibro-acoustic control via dual-mechanism: Local resonance and nonlinear damping	84
Dynamic behaviors of general composite beams using mixed finite elements	83
Detection of breathing cracks using physics-constrained hybrid network	83
Predicting solid electrolyte fracture by stress-mediated dendrite penetration in cracks	82
Linear calibration models for mass defects of hemispherical resonator	82
A tensile properties identification model for steels in large strain	81
Modeling of the coefficient of thermal expansion of 3D-printed composites	81
Investigation of a 2-DOF GER fluid damper in cut mode	81
Phenomenological modelling of cycling-induced damage in the metal-ion battery electrode	81
Inhomogeneous acoustic black hole lattice design for superior vibration suppression	80
Ultrasonic vibration enhanced friction stir welding of titanium to aluminum	79
Deep learning-based instantaneous cutting force modeling of three-axis CNC milling	79
Additive manufacturing-oriented concurrent robust topology optimization considering size control	79
Bioinspired acoustic meta-processor for enhancing physical and psychoacoustic functions	78
Mechanical properties of 3D auxetic structure: Emergence of transverse isotropy	78
A reinvestigation of the spring-mass model for metamaterial bandgap prediction	77

High-Fidelity Modeling of Cold Spray: Improved Constitutive Material Model and Nonlocal Mesh Sensitivity Mitigation	77
Dynamic modeling and analysis of fluid-delivering cracked pipeline considering breathing effect	76
Deep learning-based heterogeneous strategy for customizing responses of lattice structures	76
High-frequency topological corner and edge states in elastic honeycomb plates	76