Journal of the Japan Institute of Metals and Materials

Papers
(The TQCC of Journal of the Japan Institute of Metals and Materials is 1. The table below lists those papers that are above that threshold based on CrossRef citation counts [max. 250 papers]. The publications cover those that have been published in the past four years, i.e., from 2021-11-01 to 2025-11-01.)
ArticleCitations
Excellent Balance of Ultimate Tensile Strength and Ductility in a Ti-6Al-2Sn-4Zr-2Mo-Si Alloy Having Duplex α+α′ Microstructure: Effect of Microstructural Factors from Experimental Study and Machine L7
Band Gap Engineering of Semiconductors and Ceramics by Severe Plastic Deformation for Solar Energy Harvesting5
Nano Mechanical Characterization and Physical Modeling of Plastic Deformation Chapter 1: Dislocation-Grain Boundary Interaction as a Strengthening Factor5
<i>In Situ</i> Synchrotron High-Pressure X-ray Analysis for ZnO with Rocksalt Structure5
Numerical Analysis of Precipitation Kinetics in Cu-Co-P Alloy Based on Dislocation Recovery Model and N Model4
Micro-Mechanical Characterisation of Hydrogen Embrittlement and Fatigue Crack Growth Behaviours in Metastable Austenitic Stainless Steels with Microstructure Refinement4
Microscopic Strain Mapping: Functional Diversity and Their Demands4
Synchrotron High-Energy X-ray & Neutron Diffraction, and Laser-Scanning Confocal Microscopy: <i>In-Situ</i> Characterization Techniques for Bulk Nanocrystalline Metals4
Galvanic Corrosion among Ti-6Al-4V ELI Alloy, Co-Cr-Mo Alloy, 316L-Type Stainless Steel, and Zr-1Mo Alloy for Orthopedic Implants4
Microstructures of SUS304 Stainless Steel after Long-Term Service in Vacuum Carburizing Quenching3
Electron Microscopy on Mechanism of Voidage and Cracking in Si by Injection of a Permeable Infra-Red Laser3
Effects of Rotational Speed and Processing Time on Bonding Strength of Porous Aluminum and Thermoplastic Resin during Friction Welding2
Terahertz Detection Device Development and Application Development for Social Implementation: from Non-Destructive Testing to Crystal Growth2
Erratum: Work-Hardening Phenomena in Face-Centered Cubic Metal Crystals2
Effects of Ni Content on Particle Size of Secondary Phase in Cu-Based Alloys with Liquid Immiscibility by Laser-Melting2
Erratum: Effect of Impurity Ions and Additives in Solution of Copper Electrorefining on the Passivation Behavior of Low-Grade Copper Anode2
Mechanical and Rotating Bending Fatigue Properties of 18Cr-4.8Ni-0.03C Stainless Steel in High-Pressure Hydrogen Environment2
Perpendicular Magnetic Properties on hcp-Co<sub>80</sub>Pt<sub>20</sub> Stacked Films with Oxide Seed Layers2
Low Temperature Oxidation-Sintering Behaviors of Cu Fine Particles2
Production of Spherical Electrolytic Copper Powder from the Solution Containing Polyethyleneimine2
Effect of Electropolishing Conditions on the Outgassing Properties of Stainless Steel Surface Electropolished by Wiping and Immersion Methods2
Room-Temperature-Nitriding of Pure Titanium Using Scanning Cyclic Press in a Nitrogen Environment2
Antibacterial Properties of TiO<sub>2</sub> Layers Formed by Au-Sputtering and Thermal Oxidation of Titanium under Visible Light2
Relationship between Grain Refinement, Carbon Content and Austenite Stability Resulting in High Yield Point of 1600 MPa and Huge Lüders Deformation in SUS301 Steel1
Acceleration of Isothermal ω Phase Formation by Oxygen Addition in Ti-Nb Alloys during Cooling Process1
Effects of Grain Size and Tensile Direction on Strain Rate Sensitivity of Tensile Properties in Pure Titanium Cold-Rolled Sheet1
Recent Advance of Metallic Materials toward Next Generation Electronics1
Dimensional Changes of Selectively Laser-Melted AlSi10Mg Alloy Induced by Heat Treatment1
Effect of Surface Layer and Hydrogen on the Fatigue Strength of an Al-4％Ge Alloy1
Effect of Lattice Parameters of Master Pattern on EBSD Indexing via Pattern Matching1
The Effect of Aluminum Oxide Layer and Annealing Atmosphere on Diffusion Behavior of Ni/Al Film1
Deposition of TiC Film by Microwave Sheath-Voltage Combination Plasma1
Effects of High-Pressure Torsion on Mechanical Properties of Biocompatible Ti-6Al-7Nb Alloy1
Prediction of Carbon Concentration in Steel by Ultra Rapid Carburizing above Eutectic Temperature1
<i>Ab Initio</i> Local-Energy and Local-Stress Calculations for Materials Science and Engineering1
Substance Flow Analysis of Antimony in Japan Focused on Recycling of Used Flame Retardant Assistant1
Work-Hardening Phenomena in Face-Centered Cubic Metal Crystals1
Progress and Perspective in the Coercivity Analysis of Permanent Magnets via Large Scale Micromagnetic Simulations1
Principle of Creep Strengthening for Polycrystalline Ni-20 mass％ Cr Solid Solutions1
<i>In Situ</i> Synchrotron X-ray Analysis: Application of High-Pressure Sliding Process to Ti Allotropic Transformation1
Orientation Dependence on Bending Deformation Behavior of Pure Zinc Single Crystals1
Factors Influencing Roundness and Area of Graphite Particles on Microstructure and Graphite Nodularity Based on Japanese Industrial Standards in Spheroidal Graphite Cast Iron Castings1
Influence of Co-Deposited Hydrogen on Microstructure of Electrodeposited Platinum Films from Chloro-Complex Solution1
Nano Mechanical Characterization and Physical Modeling of Plastic Deformation Chapter 2: Strengthening Mechanisms by Various Lattice Defects1
Superfunctional Nanomaterials by Severe Plastic Deformation1
Magnetic Domain Structure Observation for Initial Magnetization and Demagnetization Processes of a Nd-Fe-B Hot-Deformed Magnet Using Soft X-ray Magnetic Circular Dichroism Microscopy1
Blackening of Electrodeposited Nickel Films by Adding Nitrate Ions and Its Mechanism1
Effect of Additional Element on Local Mechanical Properties of High Purity Aluminum Alloys by Nanoindentation1
Corrosion Resistance of Hot-Stamped Zinc-Coated Steel Sheet with a Coating Layer of the α-(Fe, Zn) Phase1
Erratum: Kink Formation through Creep Deformation and Possibility of Kink Strengthening in Ti<sub>3</sub>SiC<sub>2</sub>-MAX Phase1
Effect of Solution Heat Treatment on Dendritic Segregation and Creep Strength of Ni-Base Single Crystal Superalloy TMS-2381
Orientation Dependence of High Temperature Compressive Behavior of Textured Ti<sub>3</sub>SiC<sub>2</sub>1
0.10068798065186