OOIR: Observatory of International Research

Papers

(The H4-Index of Vacuum is 46. The table below lists those papers that are above that threshold based on CrossRef citation counts [max. 250 papers]. The publications cover those that have been published in the past four years, i.e., from 2022-01-01 to 2026-01-01.)

Article	Citations
Enhancement of longitudinal mode characteristic of quantum cascade laser by high-order tilted asymmetric surface grating	245
Encapsulation of interdigitated electrodes by PTFE coatings via closed batch initiated chemical vapor deposition	102
Rational selection of the oxygen source for atomic layer deposition Al2O3 insulators	95
Structure-fractal-property correlation of multiphase steel	88
Effects of vacuum annealing on the phase constituents and mechanical properties of the AlxCrFeMn2-xNi multiprincipal component alloys	83
AISI 316L stainless steel modification by surface alloy and a-C:H:SiOx coating synthesis	81
Synthesis mechanism and applications of edge-controlled diamond films	80
Influence of low dose rate gamma radiation on breakdown voltage and electrical breakdown time delay of working gas Geiger-Muller chamber	78
Synthesis of Ag/r-GO/ZnO nanocomposite on nickel foam for achieving efficient photoelectrochemical sensing of hydrogen peroxide	74
Secondary electron yield reduction of 316L stainless steel prepared by selective laser melting and surface remelting for electron cloud inhibition	74
Investigation of the influence of orifice length in a magnetron-based gas aggregation source on nanoparticle flow – Experiment and modeling	73
Optimal preparation of AlN thin films on sapphire substrate and its effective validation in SAW resonators	72
Simultaneous experimental verification of indirect thrust measurement method based on Hall-effect thruster and plasma plume	72
Experimental study on laser-induced arc discharge characteristics of spacecraft high-voltage solar array	72
Characterization of Fe nanoparticles on SrTiO3 (001) using X-ray photoelectron diffraction (XPD)	69
P-V-T Equation of state of gold to high pressure and temperature, derived from statistical moment method	68
Preparation, microstructure, three-point bending strength and permeability of a vacuum sintering porous plate	68
Experimental characterization of flat indentation creep behaviour of Inconel 617	66
Mesoscopic scale rearrangements of graphite nanoflake open edges under mild annealing treatments	64
A mathematical model for dehydrogenation of molten steel in the Vacuum degasser	62
Gas-phase parameters and densities of atomic species in Cl2 + O2 + Ar plasma: Effects of O2/Ar and Cl2/Ar mixing ratios	62
Lunar in-situ ironmaking through laser-assisted flash vacuum pyrolysis of iron oxide	61
Fatigue crack growth rate of AISI 4140 low alloy steel treated via shot peening and plasma nitriding	61
Coulomb explosion of powders under fast pressure decrease	61
Ga2Se3-based Ovonic Threshold Switching selector for high-density memory applications	58

Enhanced corrosion resistance of Mg17Al12 compounds by Ce modification	57
Synthesis of oxygen-rich carbon materials as metal-free catalysts for oxygen reduction reaction in seawater electrolyte	55
Molecular dynamics simulations of the evolution of primary radiation damage in Ti-6Ta alloy for spent nuclear fuel reprocessing	55
Noise analysis of dry scroll vacuum pump based on experiment and CFD	55
First-principles calculations to investigate mechanical, thermal, oxidation and hydrogen properties of Y, Zr and Nb alloyed U3Si2	55
Heteroatom doped cellulose nanocrystals (CNC) with chiral nematic liquid crystal interface for high efficiency removal of ciprofloxacin	53
Investigation of vacuum arc modes in 252 kV single-break vacuum interrupters based on deep learning image recognition	52
Modulated electrical transport properties and enhanced thermoelectric performance in tellurium by compositing with copper and doping with antimony	52
Exploring the basal/prismatic slip transfer at grain boundaries in magnesium: A molecular dynamic simulation	52
Dependence of spectral purity of Gd plasma emission around 6.7 nm on laser irradiation conditions	51
Deconvolution of high-resolution depth profiling data with sputtering induced roughness for reconstruction of nano-layer structure	50
Bottom-up stripping of graphene with controlled oxidation behaviors towards supercapacitors energy storage	50
A comparative study of carbon nanotubes and graphene for metal matrix Composites: Insights from simulation and experimentation	49
Influence of the growth rate during Nb film pulsed laser deposition on the sapphire R-plane	49
Bi2Ce2O7 nanoparticles synthesized using Elaeis guineensis Jacq. Leaf extracts and its potential for photocatalytic application	49
Effect of gas path optimization design in casting furnaces on the production yield and quality of polysilicon ingots	48
Foam-like GaN: Study on the controlled tuning of pore size by R group change in amino acid etchant and its ultra-high photocurrent response	48
Accelerated elimination of residual B2 phase in TiAl-based alloys by low-temperature annealing plus stretching	48
Study on multi-field composite strengthening, surface integrity, and microstructural evolution mechanism of 7075-T6 aluminum alloy	46
Surface properties of rhodium at various temperatures and pressures	46
Effects of vacancies on the electronic structures and photocatalytic properties of g-C3N4	46