OOIR: Observatory of International Research

Papers

(The H4-Index of Materials Letters is 39. The table below lists those papers that are above that threshold based on CrossRef citation counts [max. 250 papers]. The publications cover those that have been published in the past four years, i.e., from 2022-05-01 to 2026-05-01.)

Article	Citations
Anomalous reaction of Saucedo-etching on CdZnTeSe crystal	108
Flexible nonlinear photonics of heterostructured MXene-derived quantum dots	106
Optimized preparation of MoS2/C nanosheets for enhanced sodium-ion battery anode	75
NH3 sensor based on sc-SWCNTs/Thiophene-Containing polymer composite for human health monitoring	67
Synthesis and characterization for structural and optical properties of FASnI2Br for perovskite solar cell applications	66
Enhanced extraction of calcium alginate and 2D nanocellulose from brown algae (Sargassum spp.)	64
Editorial Board	60
One-step synthesis of needle-like lanthanum-doped TiO2 nanomaterials and their photoconductivity activity in air medium	58
Simulation and experimental studies of the influencing factors of oleic acid modified nanoparticles in magnetic nanofluids	54
Editorial Board	52
Stable, large-grained FAMAPbI3 PV absorber layer through rapid radiative thermal annealing (RTA)	52
Morphological evolution of electrochromic nanosheet-structured nickel-cobalt oxide thin films	52
HCOO− ions mediated formation of cupric subcarbonate (Cu2(OH)2CO3) with various hierarchical micro/nanostructure via facile and mild solution route	49
A novel strategy of regional microstructure design in manufacturing	48
Heat shrinking polymer based film reinforced with two dimensional carbon nitride with enhanced barrier and thermal properties	47
Strong magnetic response regulated by layer-stacking perturbations in an Aurivillius-phase oxide	47
Enhanced phase transfer of Ag-nanospheres using amine-containing amphiphiles for sensitive chemical detection in nonaqueous environments	46
Influence of atmospheric conditions on the formation and structural properties of two-dimensional SbSI films	44
Novel attempts for the assembly of tannic-based coatings in ethanol media	43
Ink formulation and printing of electrolyte for a doped ceria solid oxide fuel cell	43
Wavelength determination of ion-induced ripples	43
Visualization of bandgap energy fluctuation in InGaN quantum wells	43
Microstructure and properties of melt-spun AlYNiCr multi-component amorphous alloy ribbons through partial substitution of Cr for Ni	42
Multifunctional superelastic graphene aerogels derived from ambient-dried graphene oxide/camphene emulsions	42
Casting of Fe-(2–12)Mn-(4–14)Al-(0.09–0.7)C low-density steel via artificial slag practice	42

Effect of Wire-EDM textures on corrosion performance of Bio-Degradable Mg alloy	42
Dried figs like nitrogen-doped graphene oxide anchored cobalt-doped Fe3O4 nanoparticle as sulfur host for high performance Li-S battery	42
Evaluating magnetic degradation in FeCo-V alloys for high-output and compact electric motors: A multiscale-multiphysics approach	41
Effect of natural aging on mechanical properties and corrosion behavior of 2219 aluminum alloy cold sprayed coatings	41
Eliminating embrittlement of GH4065A superalloy at intermediate temperature by a novel grain boundary strengthening mechanism	40
Enhancing the corrosion resistance of selective laser melting Ti6Al4V alloy by hot stamping post-treatment	40
Stability of amorphous Li-La-Zr-Ta-O coating for high-voltage cathodes in sulfide-based solid-state batteries	40
Synthesis of nanostructured sphere-like copper oxide by microwave spray pyrolysis	39
A High-Capacity black Phosphorus-Graphite-Sn anode for Lithium-ion batteries	39
Effect of preheating temperature on the defects in pulsed laser welding of sheet AZ31 magnesium alloy	39
Microstructural and thermal characterization of polyethylene and basalt fiber-reinforced natural zeolite-based engineered geopolymer composites	39
Green synthesis of porous carbon for supercapacitors from pine cone/phoenix tree fruit fluff by hydrothermal pre-activation method	39
Scalable fabrication of PVDF/SiO2-PTFE fiber membrane for effective daytime radiative cooling	39
High strain rate induced shear banding within additively manufactured AISI 316L	39