OOIR: Observatory of International Research

Papers

(The median citation count of Sadhana-Academy Proceedings in Engineering Sciences is 3. The table below lists those papers that are above that threshold based on CrossRef citation counts [max. 250 papers]. The publications cover those that have been published in the past four years, i.e., from 2021-11-01 to 2025-11-01.)

Article	Citations
Delay dependent wide area damping controller design for a linear parameter varying (LPV) power system model considering actuator saturation and changing environmental condition	17
Dynamics of single-link manipulator under a novel control law	16
Effect of industrially processed glass fibre dust on mechanical, thermal and morphological properties mixed with LLDPE for rotational molding process	15
Improvement of microstructure and hardness property of MMA welded ADI workpiece using newly developed electrode	14
Comparison between mechanical behaviors of wire ropes with distinct contact modes based on the finite element method	14
Performance analysis of deep neural networks through transfer learning in retinal detachment diagnosis using fundus images	13
Computational analysis of two-phase flow in a converging-diverging propulsion nozzle suitable for water transport	13
Reduced component high voltage boost single-source switched capacitor inverter	12
Continuous review inventory system for intuitionistic fuzzy random demand under service level constraint	11
Vertical nonlinear response of single and 2 × 2 group pile under strong harmonic excitation	11
Parametric optimization of CVD process for DLC Thin film coatings: a comparative analysis	11
Experimental studies on dry machining behavior of Ti-6Al-4V using carbide, cermet, and SiAlON tools	11
Analysis of box and ellipsoidal robust optimization, and attention model based reinforcement learning for a robust vehicle routing problem	11
Workplace-based assessment and intervention design for waste sorting tasks in a developing country	10
Improvement of torque and permanent magnet operating flux density in a novel flux-intensifying spoke PMSM based on peripheral and internal barriers	9
Polarization independent frequency selective surface for marine and air traffic radar applications	9
A quantum secure ID-based cryptographic encryption based on group rings	8
A modified FxLMS fluid flow control model for convectively unstable disturbances	8
A review on coronavirus survival on impermeable and porous surfaces	7
Design, simulation, fabrication and testing of LIM for EML	7
Conjugate steady natural convection analysis around thick tapered vertical pipe suspended in the air	7
A Quantum Resistant Anonymous Poxy Signature Scheme	7
Investigations on current waveform unbalance in a conventional switched reluctance motor even under healthy operating conditions at steady state	7
Effortless detection of premature ventricular contraction using computerized analysis of photoplethysmography signal	7
Machine learning-based modeling of saturated hydraulic conductivity in soils of tropical semi-arid zone of India	6

An investigation on heat and mass transfer characteristics during spray drying of saline water	6
Optimizing parameters effective on built-up edge in internal gear flowforming process	6
Loop based classification of planar scissor linkages	6
Comprehensive nonlinear buckling analysis of a cracked cylinder under axial loading	5
Comparative analysis of CycleGAN and AttentionGAN on face aging application	5
Broadband circularly polarized dielectric resonator antenna for UWB applications	5
Mathematical modelling of PV array under partial shading condition	5
Thermal management and optimization of adsorption vessels for CO2-based green refrigeration systems: A heat and mass transfer approach	5
TaskMUSTER: a comprehensive analysis of task parameters for mixed criticality automotive systems	5
A contemporary investigation of metal additive manufacturing techniques	5
Influence of acetone addition into gasoline for i-DSI engine	5
New high frequency memristorless and resistorless meminductor emulators using OTA and CDBA	5
Ordering and pricing decisions of regular products in a supply chain with the effects of product-specific gift cards	5
Enhancing the aggregate diversity with mutual trust computations for context-aware recommendations	5
A comparative study of the pulsating flames with different air inlet port geometrical shape	4
Fluid flow and heat transfer in microchannel with and without porous medium under constant heat flux	4
On-line field balancing technique using virtual trial unbalances in rotor-bearing system incorporated with active magnetic bearing	4
Bond slip behaviour of deformed bar embedded in sustainable concrete at elevated temperature	4
Effect of free stream turbulence intensity on corrugated airfoils at ultra low Reynolds numbers	4
Thermodynamic analysis of sensible heat storage based double pass hybrid solar air heater with and without reflector	4
Performance enhancement in WEDM of nitronic-30 using latent heat energy	4
Detection of breast tumor using inset-fed microstrip patch antenna at MICS band for implantable applications	4
Performance characterization of modified random direction mobility model in UAVs cellular network	4
Presenting an economic interaction bi-level model between electricity retailer and customer in bilateral electricity market contract	4
Comparative experimental study on application feasibiility of MTCVD TiCN-Al2O3-TiOCN multi-layer coated carbide and PVD TiN single layer coated composite ceramic inserts during dry machining of Ti-6Al	4
Women friendly pedal operated cashew nut desheller: a machine to alleviate drudgery	4
Maximizing energy efficiency using Dinklebach’s and particle swarm optimization methods for energy harvesting wireless sensor networks	4
Electronic circuit implementation of the compartmental models for population dynamics of COVID-19 like epidemics	4
An improvement of Bengali factoid question answering system using unsupervised statistical methods	3
A QoS-aware service discovery and selection mechanism for IoT environments	3
A new very high output resistance FVF based class-A super-cascode CCII	3
A novel methodology to update table in air data system of a high performance fighter aircraft	3
Risk-based performance of regional-market management considering information gap decision theory and demand response program	3
Development of temporal model for analysis of heat transfer equipment subjected to fouling	3
Image content based secure reversible data hiding scheme using block scrambling and integer wavelet transform	3
Exponential state observer based finite time control of fully active hybrid energy storage system	3
Influence of moisture on microwave-induced shape memory thermoplastic polyurethane/graphene nanoplatelets composite	3
Study on IoT networks with the combined use of wireless power transmission and solar energy harvesting	3
Influence of drainage blanket clogging on response of homogeneous earthen dams	3
Explicitly unsupervised statistical machine translation analysis on five Indian languages using automatic evaluation metrics	3
A continuum model for predicting strain evolution in carbon fiber-reinforced composites subjected to cyclic loading	3
Floating capacitance multiplier realization based on commercially available integrated circuits	3
The effect of deep cryogenic treatment on the wear properties of AZ91 magnesium alloy in dry and in 0.9 wt% NaCl medium	3