OOIR: Observatory of International Research

Papers

(The TQCC of Sadhana-Academy Proceedings in Engineering Sciences is 5. The table below lists those papers that are above that threshold based on CrossRef citation counts [max. 250 papers]. The publications cover those that have been published in the past four years, i.e., from 2021-09-01 to 2025-09-01.)

Article	Citations
Delay dependent wide area damping controller design for a linear parameter varying (LPV) power system model considering actuator saturation and changing environmental condition	19
Analysis and design of efficient SiC-based load-resonant converter with advanced features for arc welding applications	18
Dynamics of single-link manipulator under a novel control law	17
Effect of industrially processed glass fibre dust on mechanical, thermal and morphological properties mixed with LLDPE for rotational molding process	16
Performance analysis of deep neural networks through transfer learning in retinal detachment diagnosis using fundus images	14
Comparison between mechanical behaviors of wire ropes with distinct contact modes based on the finite element method	14
Reduced component high voltage boost single-source switched capacitor inverter	14
Computational analysis of two-phase flow in a converging-diverging propulsion nozzle suitable for water transport	13
Improvement of microstructure and hardness property of MMA welded ADI workpiece using newly developed electrode	13
Torsion strength of TIG welded similar and dissimilar metal joints of ASME SA213 Gr.T11 and BS3059:1987 PT1 ERW320	13
Vertical nonlinear response of single and 2 × 2 group pile under strong harmonic excitation	11
Analysis of box and ellipsoidal robust optimization, and attention model based reinforcement learning for a robust vehicle routing problem	11
Continuous review inventory system for intuitionistic fuzzy random demand under service level constraint	11
Design and manufacturing of an inductive liquid food heat treatment-filling system	11
Influence of machining behavior on severe deformation and corrosion resistance of end milled Nimonic 263 alloy	11
Parametric optimization of CVD process for DLC Thin film coatings: a comparative analysis	10
Terahertz radiation from silicon carbide charge plasma avalanche transit time source	9
Heat transfer during diffusion-controlled unidirectional solidification of binary mixtures: effect of material advection	9
Game approach for access point selection and bandwidth allocation in co-existing WBANs	9
Experimental studies on dry machining behavior of Ti-6Al-4V using carbide, cermet, and SiAlON tools	8
Workplace-based assessment and intervention design for waste sorting tasks in a developing country	8
An experimental study on mechanical properties and wear of A380/nB4C composites fabricated using two different liquid state processes	8
Improvement of torque and permanent magnet operating flux density in a novel flux-intensifying spoke PMSM based on peripheral and internal barriers	8
Solving grid scheduling problem using an amalgam of swarm and traditional approach	7
A modified FxLMS fluid flow control model for convectively unstable disturbances	7

Effortless detection of premature ventricular contraction using computerized analysis of photoplethysmography signal	7
Polarization independent frequency selective surface for marine and air traffic radar applications	7
A Quantum Resistant Anonymous Poxy Signature Scheme	7
A quantum secure ID-based cryptographic encryption based on group rings	7
A review on coronavirus survival on impermeable and porous surfaces	6
Conjugate steady natural convection analysis around thick tapered vertical pipe suspended in the air	6
On compressible circular Rayleigh problem of hydrodynamic stability	6
Investigations on current waveform unbalance in a conventional switched reluctance motor even under healthy operating conditions at steady state	6
Ballistic impact performance of ultra-high molecular weight polyethylene (UHMWPE) composite armour	6
Design, simulation, fabrication and testing of LIM for EML	6
Integrating synchrophasor technology for the improvements in system integrity protection schemes under stressed conditions	5
On flexural and pull out properties of smart polymer based 3D printed functional prototypes	5
Loop based classification of planar scissor linkages	5
New high frequency memristorless and resistorless meminductor emulators using OTA and CDBA	5
Ordering and pricing decisions of regular products in a supply chain with the effects of product-specific gift cards	5
Comprehensive nonlinear buckling analysis of a cracked cylinder under axial loading	5
TaskMUSTER: a comprehensive analysis of task parameters for mixed criticality automotive systems	5
An investigation on heat and mass transfer characteristics during spray drying of saline water	5
Thermal management and optimization of adsorption vessels for CO2-based green refrigeration systems: A heat and mass transfer approach	5
Optimizing parameters effective on built-up edge in internal gear flowforming process	5
GSEIM: a general-purpose simulator with explicit and implicit methods	5
In situ determination of the mechanical performance of the steel rods anchored on an existing masonry building wall	5
Effect of humidity on the evolution of COVID-19 droplets distribution in extreme in-homogeneous environment	5
Machine learning-based modeling of saturated hydraulic conductivity in soils of tropical semi-arid zone of India	5
Ecosystem model for healthcare platform	5
Comparative analysis of CycleGAN and AttentionGAN on face aging application	5