Surface & Coatings Technology

Papers
(The H4-Index of Surface & Coatings Technology is 53. The table below lists those papers that are above that threshold based on CrossRef citation counts [max. 250 papers]. The publications cover those that have been published in the past four years, i.e., from 2022-01-01 to 2026-01-01.)
ArticleCitations
Editorial: Anti-corrosion coatings249
Influence of anodically grown TiO2 nanotubes on shear strength and fatigue behavior of pure titanium167
Effect of strip entry temperature on the interfacial layer and corrosion behavior of galvanized steel141
Optimization of deposition parameters and performance analysis of Nb-Zr-N composite films112
Effects of in-situ synthesized carbides on microstructure and properties of FeCoCrNiMo0.2 / graphene composite coatings via laser cladding111
Surrogate model for energy release rate and structure optimization of double-ceramic-layers thermal barrier coatings system106
Development of Ti/Ti-DLC multilayers on magnesium alloys. Part 1: Microstructure and mechanical properties99
Thickness-controlled porous NiO films by Ni(OH)2/alginate layer-by-layer assembly99
Thermal evolution of yttrium tetraboride thin films – A candidate for high temperature applications98
Formation of corrosion-resistant coatings on cast AZ91D magnesium alloy using pulse electrolysis and the importance of coating morphology96
Amorphous oxide coating deposited by plasma electrolytic oxidation on the inner walls of seamless Ti-3Al-2.5V tubes95
Editorial: MXenes and their hybrids – Expanding the frontier of 2D materials89
Plasma electrolytic oxidation of as-cast and heat-treated binary Al-Ni alloys84
Effects of molten silicate reactivity on high temperature erosion behavior of plasma sprayed Yb2Si2O7-based EBCs77
Microstructure and tribological properties of Al-30Si-5Cu composite coating reinforced with ceramic phases synthesized in situ by plasma spraying76
Corrosion and friction behaviours of MoSi2/MoS2 nanoparticles incorporated tinted coating on Ti6Al4V alloy74
Enhanced friction and wear resistance of bamboo surfaces via ZrP-WPU composite coatings72
Effect of bias voltage and heating power on the structural and tribo-mechanical properties of chemically complex TiSiBCN nanocomposites71
TIG-clad Fe-based AlCoCrNiTi0.5 high-entropy alloy coating on low-carbon steel: microstructure, microhardness, and corrosion resistance71
Preparation of hollow MgO nanosorbents via the templating method and study of their adsorption mechanism68
Nano-mechanical properties of Mo coating prepared on Invar alloy substrate by double glow plasma surface alloying66
Effect of insertion layers on the environmental stability of TiO2/SiO2 anti-reflective coatings on PMMA substrates65
Highly transparent aluminum silicon oxy nitride permeation barriers for optoelectronic devices65
Laser assisted electrodeposition of binary metallic alloys from water-based electrolytes: The case of palladium‑platinum64
Rational design of pH-responsive hydrogel micropatterns on magnesium alloy with enhanced biological activity64
Carbon nanotube mat/boron nitride composite materials for aerospace applications64
Processing of Co-base/C-nanotubes compound coatings on D2 steel using plasma transferred by arc: Tribological and mechanical performance64
Editorial Board64
Microstructural evolution and interfaces in cold sprayed hybrid aluminum alloy powders of different hardness64
Residual stresses induced by Inconel 718 cold gas repair spray of large cavities — On the influence of the sample geometry64
Alleviating internal stress in diamond-like carbon films for enhanced tribological performance under high contact pressure via interface texturing63
Intercalation of decanoate anions (C10) in layered double hydroxide Mg Al and its application as controlled-release corrosion inhibitor of steel63
Review of the state of art of Li-based inhibitors and coating technology for the corrosion protection of aluminium alloys62
Interface phase and mechanical properties of (Fe50Mn30Co10Cr10)100-xAlx laser cladding layer with adjustable Al content62
Unusual indentation depth dependent hardness and creep behaviors in NbMoTaW films at the nanoscale62
Exploring the microstructure and wear-resistance of Fe-Cr-C-W arc cladding coatings by laser remelting61
Effect of oxygen flow rate ratio on crystalline phase and properties of copper oxide films prepared by room-temperature high-power impulse magnetron sputtering59
Synergistic oxidation-corrosion and the arresting role of a NiCr interlayer in the failure of HVOF-sprayed Cr3C2-NiCr coatings59
In-depth study of the dry-anodizing process on Ti6Al4V alloys: Effect of the acid content and electrical parameters59
Influence of multilayer nanoarchitecture on phase transformations in the Ti-Cr-Zr system58
Friction surfacing of aluminum alloys on Ti6Al4V - Investigation of process parameters, material deposition behavior and bonding mechanisms58
Plasma sprayed graphene reinforced titanium nitride composite coating: An effective solution for mitigating the corrosion attack58
Investigation of microstructural changes of Pt-Al-7% YSZ coating during high-temperature hot corrosion and its effect on tensile properties of coated Rene-80 superalloy at 950 °C57
Area selective atmospheric pressure PECVD of organosilicon precursors: Role of vinyl and ethoxy groups on silicon oxycarbide deposition patterns - A case study57
Structure, mechanical properties and tribocorrosion behaviours of superhard TiSiCN nanocomposite coatings57
Changes in protective properties of zirconia and silica sol-gel layers over time55
Effect of prior copper-coating on the microstructural development and corrosion behavior of hot-dip galvanized Mn containing high strength steel sheet55
Passivation characteristics and corrosion behavior of S32202 duplex stainless steel in different temperatures polluted phosphoric acid54
Oxidation behavior of AlCoCrFeNiSix high entropy alloy bond coatings prepared by atmospheric plasma spray54
Influence of β-SiC phase contents on hardness and elastic modulus of multilayered diamond/β-SiC composite coatings54
Influences of the near-spherical 3D pore on failure mechanism of atmospheric plasma spraying TBCs using a macro-micro integrated model54
Microstructure and properties of Ta-reinforced cobalt based composite coatings processed by direct laser deposition54
Role of residual stress and ultrafine grain layer at the surface introduced by water jet cavitation peening in stress corrosion cracking of alloy 600 in high temperature water53
HVOF-sprayed surface coating with various compositions of Co-NiCrAlY-Al2O3 to minimize sediment erosion in hydraulic turbines53
Wear-resistance enhancement of graphene oxide/zirconia nanosheets composite coatings based on 2D-2D interlayer sliding structure53
The mechanical properties and damage mechanism of TiAlN/TiZrHfNb coatings subjected to dynamic cyclic nano-impact53
Ex-situ observation of microstructure evolution and electrical resistance transition in micro joints under electron current stressing53
A fluid-solid coupled model for particle velocity and validation in spiral bevel gear shot peening53
0.32453608512878