Surface & Coatings Technology

Article	Citations
Editorial: Anti-corrosion coatings	190
Editorial: MXenes and their hybrids – Expanding the frontier of 2D materials	103
Highly transparent aluminum silicon oxy nitride permeation barriers for optoelectronic devices	102
Residual stresses induced by Inconel 718 cold gas repair spray of large cavities — On the influence of the sample geometry	101
A novel copper surface modification approach based on pinless friction stir surface processing technique with ultra-low heat input	98
Influence of β-SiC phase contents on hardness and elastic modulus of multilayered diamond/β-SiC composite coatings	91
Influence of multilayer nanoarchitecture on phase transformations in the Ti-Cr-Zr system	89
In-depth study of the dry-anodizing process on Ti6Al4V alloys: Effect of the acid content and electrical parameters	87
Changes in protective properties of zirconia and silica sol-gel layers over time	82
Improved oxidation resistance of AIP NiCrAlYSi coatings by applying positive bias	82
Editorial Board	81
Wear-resistance enhancement of graphene oxide/zirconia nanosheets composite coatings based on 2D-2D interlayer sliding structure	81
Alleviating internal stress in diamond-like carbon films for enhanced tribological performance under high contact pressure via interface texturing	78
Influence of laser shock processing without coating on the microstructure and tribological behavior of super duplex stainless steel	77
Microstructure evolution and thermal shock properties of PEO coatings on a TiAl alloy	77
Intercalation of decanoate anions (C10) in layered double hydroxide Mg Al and its application as controlled-release corrosion inhibitor of steel	75
Structure and tribological properties of “carbon steel – VC containing coating” compositions formed by non-vacuum electron-beam surfacing of vanadium-containing powder mixtures	72
Polymer infiltration synthesis of inorganic nanoporous coatings: Does polymer template affect their properties?	71
Microstructure and tribological properties of Al-30Si-5Cu composite coating reinforced with ceramic phases synthesized in situ by plasma spraying	71
Plasma electrolytic oxidation of as-cast and heat-treated binary Al-Ni alloys	70
Microstructure and properties of Ta-reinforced cobalt based composite coatings processed by direct laser deposition	70
In-situ growth and mechanism of MgAl-NO3-LDHs film on Ti6Al4V via one-step hydrothermal treatment with a high concentration of alkaline growth solution	69
Effects of the substrate state beneath the coating-substrate interface on fatigue properties of micro-arc oxidation coated 6082-T6 aluminum alloy	68
Friction surfacing of aluminum alloys on Ti6Al4V - Investigation of process parameters, material deposition behavior and bonding mechanisms	67
Comparative study on the annealing of cold-sprayed boron nitride nanosheet/copper coating using spark plasma sintering and atmosphere furnace	67

Manufacturing and the process-structure-property correlation of detonation sprayed iron coatings under an unconventional coating deposition mechanism	65
Evaluation of mechanical properties and in vitro biocompatibility of TiZrTaNbHf refractory high-entropy alloy film as an alternative coating for TiO2 layer on NiTi alloy	65
Effect of bias voltages and interlayer design on microstructure, mechanical properties, and adhesion performance of AlCrSiN coatings deposited using HiPIMS	64
High-sensitivity reflectometric interference spectroscopy for label-free glucose detection using facile one-step anodic alumina	64
Biopolyurethane coatings with silica-titania microspheres (MICROSCAFS®) as functional filler for corrosion protection	64
Hydrothermal temperature-dependent growth and tribological performance of Mg–Al–Ce LDH/CeO₂ composite coatings on AZ31 Mg alloy	64
Time-varying evolutionary mechanism analysis of the multiphase flow during high-velocity oxygen-fuel (HVOF) thermal spraying WC-12Co particle	64
Processing of Co-base/C-nanotubes compound coatings on D2 steel using plasma transferred by arc: Tribological and mechanical performance	63
Amorphous oxide coating deposited by plasma electrolytic oxidation on the inner walls of seamless Ti-3Al-2.5V tubes	63
Effects of molten silicate reactivity on high temperature erosion behavior of plasma sprayed Yb2Si2O7-based EBCs	63
Effect of bias voltage and heating power on the structural and tribo-mechanical properties of chemically complex TiSiBCN nanocomposites	63
Ex-situ observation of microstructure evolution and electrical resistance transition in micro joints under electron current stressing	63
Interface phase and mechanical properties of (Fe50Mn30Co10Cr10)100-xAlx laser cladding layer with adjustable Al content	62
Nano-mechanical properties of Mo coating prepared on Invar alloy substrate by double glow plasma surface alloying	62
Multiple oxidation mechanism of Al and Ti doping Haynes244 alloy under elevated temperature	62
Preparation and biological evaluation of TiO2/HA composite coatings on TC4 fabricated by micro-arc oxidation	61
FeCrCoNiAlTiWMoTaNb high entropy alloy coatings fabricated by wire–powder hybrid additive manufacturing: Microstructural and tribological behavior	61
Superior performance of amorphous alumina coatings over polycrystalline alumina for fusion reactor applications	61
Study on properties and tribological behaviors of silicon nitride-based Ti-DLC films	60
Functionalized graphite nanosheet/organosilicon composite coatings with soft-hard structures: Excellent wear resistance and hydrogen barrier properties	60
Influence of anodically grown TiO2 nanotubes on shear strength and fatigue behavior of pure titanium	60
Enhanced friction and wear resistance of bamboo surfaces via ZrP-WPU composite coatings	60
Structure, mechanical properties and tribocorrosion behaviours of superhard TiSiCN nanocomposite coatings	59
Optimization of deposition parameters and performance analysis of Nb-Zr-N composite films	59
Corrosion and friction behaviours of MoSi2/MoS2 nanoparticles incorporated tinted coating on Ti6Al4V alloy	59
Corrosion and mechanical performance of novel electrochemical oxidation coatings on AZ31 magnesium alloys for biomedical applications	59
Study on oxidation resistance and Al diffusion of Cr1-xAlx coatings with different low Al content	59
Microstructural evolution and interfaces in cold sprayed hybrid aluminum alloy powders of different hardness	58
Enhanced wear resistance of CoCrFeNiMo0.3Ta0.2 high-entropy alloy coatings fabricated by high-speed laser cladding and low-speed laser cladding: The role of graphene and solidification kinetics	58
Development of Ti/Ti-DLC multilayers on magnesium alloys. Part 1: Microstructure and mechanical properties	58
Effect of laser shock peening on plasma nitriding microstructure and properties of H13 steel	58
Laser cladding Ni3Si/CrNi3 reinforced metal matrix composite coatings: Microstructure evolution, tribological behavior and oxidation resistance	58
Fabrication of amorphous AlMo0.5NbTa0.5TiZr RHEA coatings and the impact of deposition temperature on microstructure and properties	58
Synergistic oxidation-corrosion and the arresting role of a NiCr interlayer in the failure of HVOF-sprayed Cr3C2-NiCr coatings	58
Controlling microstructural gradients in laser-clad AlCoCrFeNi2.1 EHEAs: The role of faceted B2 and non-faceted FCC phase growth under rapid solidification	58
Evaluation of the abilities of atomic oxygen/ultraviolet resistance for the filled silicone rubber coating: Structures, properties, and aging mechanism	57
Corrosion-resistant and superhydrophobic nickel-based composite coating on magnesium alloy	57
Carbon nanotube mat/boron nitride composite materials for aerospace applications	57
Evaluation of film adhesion strength on textured surface: experiments and mechanisms	56
Exploring effects of molybdenum and titanium contents on microstructure and mechanical properties of CoCrNi medium entropy alloy films	56
Effects of silicon and neodymium additions on microstructures and mechanical properties of CoCrNi medium entropy alloy films	56
Mechanically tailored surface of titanium based alloy (Ti6Al4V) by laser surface treatment	56
Tailoring the microstructure and wear resistance of (Al10Ti30Zr30Nb30)100-xVx high-entropy alloy coating via V alloying and heat treatment	55
High-temperature steam oxidation resistance of Cr Si substitutional solid solution coating on Zr-4	55
TIG-clad Fe-based AlCoCrNiTi0.5 high-entropy alloy coating on low-carbon steel: microstructure, microhardness, and corrosion resistance	54
Effects of B4C particle size and content on microstructure and properties of in-situ TiB2-TiC composite coatings prepared by plasma spraying	54
A new strategy to fabricate Ti2AlC MAX coatings by the two-step laser method	54
Investigation on microstructure evolution and corrosion behavior of FeCoCrNiMoCuxSi0.2 high entropy alloy coating produced by laser cladding	54
A study integrating in-process thermal signatures, microstructure, and corrosion behaviour of AISI 316L coatings on low carbon steel substrate deposited by laser-directed energy deposition (L-DED)	53
New insights into the formation mechanism of a bare-spot defect in hot-dip galvanized coating	53

Review of the state of art of Li-based inhibitors and coating technology for the corrosion protection of aluminium alloys	53
Selective laser melted 316L stainless steels duplex-treated by shot peening and TiAlCuN coating: Elucidating the enhanced cavitation erosion resistance	53
Effect of current density on the texture, residual stress, microhardness and corrosion resistance of electrodeposited chromium coating	53
High-temperature tribological characteristics and lubrication mechanisms of NiCrAlY-MoO3/CoO composite coatings: An experimental and DFT computation study	53
Preparation of Ni-Cu-based superhydrophobic composite coatings with anti-corrosion and self-cleaning properties	52
Formation of corrosion-resistant coatings on cast AZ91D magnesium alloy using pulse electrolysis and the importance of coating morphology	52
Spallation mechanism of thermal barrier coatings with real interface morphology considering growth and thermal stresses based on fracture phase field	51
Laser cladding of B4C-Ti64 composite coating: multi-objective process optimization, and investigation on microstructure, microhardness, and wear behavior	51
Improving the oxidation resistance by forming continuous Al2O3 protective layer in alumina-forming austenitic stainless steel	51
Thickness-controlled porous NiO films by Ni(OH)2/alginate layer-by-layer assembly	51
Effect of MoS2 lubricating coatings on the corrosion behaviour of monel 400 alloy	51
The mechanical properties and damage mechanism of TiAlN/TiZrHfNb coatings subjected to dynamic cyclic nano-impact	51
Particle impact ignition-resistance of a ductile phase toughened glass-ceramic coating	51
Microstructure and dielectric properties of Al₂O₃–Cr₂O₃ composite coatings fabricated by wide-velocity range high-energy plasma spraying	50
In-situ SiC-SiCw layer enhances HfC-HfB2-SiC coatings for 2500 °C ablation	50
Influence of surface plastic deformation on oxidation behavior for low Cr content nickel superalloy: Focus on the Cr diffusion	50
Microstructure control of Ti-based conversion coatings for optimizing organic coating properties in A6063 and A3003 alloys	50
Effect of insertion layers on the environmental stability of TiO2/SiO2 anti-reflective coatings on PMMA substrates	49
Exploring the microstructure and wear-resistance of Fe-Cr-C-W arc cladding coatings by laser remelting	49
Exploring MgO/HA ceramic nano-composites for biodegradable implants: Exploring biological properties and micromechanics	49
Improving surface electrochemical polishing quality of additive manufactured AlSi10Mg by reconstituting the Si phase	49
Influence of voltage on growth and microstructure of oxide coatings on γ-TiAl alloy by cathodic plasma electrolysis in glycerin solution	49
Area selective atmospheric pressure PECVD of organosilicon precursors: Role of vinyl and ethoxy groups on silicon oxycarbide deposition patterns - A case study	49
Effect of laser power on the microstructure, mechanical properties, and tribological performance of laser-clad SnSb11Cu6 coatings on Q345 steel	48
Effect of substrate bias on the microstructure and mechanical and tribological properties of ZrNbTiMo refractory high entropy alloy film	48
Laser assisted electrodeposition of binary metallic alloys from water-based electrolytes: The case of palladium‑platinum	48
Nitriding high entropy alloy films: Opportunities and challenges	48
Enhanced mechanical and tribological properties of hydrogen-free DLC coating by introducing SiAl interlayer	48
Role of residual stress and ultrafine grain layer at the surface introduced by water jet cavitation peening in stress corrosion cracking of alloy 600 in high temperature water	48
Ablation behavior and delamination mechanism of air plasma sprayed (Gd, Yb) doped YSZ double ceramic layer thermal barrier coatings at 1500 °C	48
Effects of in-situ synthesized carbides on microstructure and properties of FeCoCrNiMo0.2 / graphene composite coatings via laser cladding	47
Slippery liquid-infused porous surfaces with long-term durable antifouling and anti-corrosion performance via bimodal structure design	47
Role of micro- and nano-CeO2 reinforcements on characteristics and tribological performance of HVOF sprayed Cr3C2-NiCr coatings	47
Passivation characteristics and corrosion behavior of S32202 duplex stainless steel in different temperatures polluted phosphoric acid	47
Friction and wear behavior of atmospheric plasma sprayed NiMoAl-Ag-hBN coatings at elevated temperatures	47
Multi-objective optimization of process parameters for rectangular laser cladding of Fe-based alloy wear-resistant coatings	47
Plasma sprayed graphene reinforced titanium nitride composite coating: An effective solution for mitigating the corrosion attack	47
Unusual indentation depth dependent hardness and creep behaviors in NbMoTaW films at the nanoscale	47
Study on microstructure and properties of laser-clad Fe-based (Ti, V)C composite coatings	47
Effect of adding copper-plated graphite on the organization and wear reduction of Copper-Nickel alloy Composite Coatings	47
Oxidation behavior of AlCoCrFeNiSix high entropy alloy bond coatings prepared by atmospheric plasma spray	46
Graphene-reinforced titanium coatings deposited by Cold Gas Spray: Study of microstructure, mechanical and wear properties	46
Characteristic, corrosion and high-temperature steam oxidation behavior of FeCrAl-coated Zr alloy by magnetron sputtering: Synergistic effect of deposition temperature and substrate bias	46
Microstructure evolution and water vapor resistance of multi-layer EB-PVD yttrium-based EBCs	46
Improving the thermal cycling lifetime of thermal barrier coatings with an atmospheric plasma-sprayed carbon-alloyed MCrAlY bond coat	46
Rational design of pH-responsive hydrogel micropatterns on magnesium alloy with enhanced biological activity	46
A fluid-solid coupled model for particle velocity and validation in spiral bevel gear shot peening	46
Growth characteristics and wear properties of micro-arc oxidation coating on Ti-6Al-4V with different laser texture shapes	45
In situ polymerized fluoropolymer coatings on aluminum particles: Tailored modulation of combustion dynamics and agglomeration suppression in composite propellants	45
Effect of nitrogen flow rates on the structural and properties of TiVCrNiSi(N) high entropy coating deposited by arc ion plating	45
Preparation of hollow MgO nanosorbents via the templating method and study of their adsorption mechanism	45
Thicker the better or thinner: Addressing the dichotomy in the case of MAO coated AZ91 Mg alloy for corrosion protection	45
Thermal shock behavior and high-temperature oxidation performance of PDC-based environmental barrier coatings on AISI 441 stainless steel	45
HVOF-sprayed surface coating with various compositions of Co-NiCrAlY-Al2O3 to minimize sediment erosion in hydraulic turbines	45
The performance of a HVOF-deposited HAp-bioactive glass composite coating on AZ31 alloy to reduce the corrosion rate in simulated body fluid: Assessment scanning electrochemical microscopy and electro	44
Synthesis of manganese oxide thin films deposited on different substrates via atmospheric pressure-CVD	44
A novel strategy to improve the corrosion resistance of SiCf/SiC composites in high-temperature combustion environments by cooperation of self-healing SiBCN and high-stability Yb2Si2O7	44
Synergistic effects of Ta and Si alloying on the long-term oxidation resistance of Ti1-xAlxN coatings	44
Comparison of CoCrNiTiMo and CoCrNiTiMoAl coatings in simulated oxidation conditions at 650 °C, 800 °C, and 950 °C temperatures	44
Improvement in electrochemical behaviour of Ti-6Al-4V alloy by ultrasonic-assisted abrasive peening	44
Reactive magnetron sputtered (Mn, Co)3O4 spinel coatings for superior element diffusion suppression and conductivity in ferritic stainless-steel interconnects of solid oxide fuel cells	44
Core shell coatings for nuclear thermal propulsion cermets	43
WITHDRAWN: Self-peeling hydrogel with strong adsorption to patina revive slumbered bronze relics by nondestructive cleaning	43
Tribological study of W-S-(C) sputtered coatings sliding against aluminium at elevated temperatures	43
Effects of post-annealing treatment on the tribological and electrochemical properties of (Ti,Al,Cr,Si,Zr)N coated steels	43
Exploring surface preparation for cold spraying on polymers	43
Corrosion behavior of Si-DLC film in simulant solutions containing CO2-H2S-Cl−	43
Crystal defect-based in-situ carburizing technology to strengthen refractory metals	43
A facile synthesis of density-tunable ZnO nanorod-array on PVTF film for biomedical application	43
Duplex plasma electrolytic oxidation/ hydroxyapatite- polydopamine coating on WE43 alloy for bone implants: Long-term corrosion resistance and biological properties	43
Editorial Board	43
Thermo-mechanical analysis of TBC-film cooling system under high blowing ratio considering the effects of curvature	42
The antifouling tris-(8-hydroxyquinoline) aluminum: Titanium dioxide coatings under visible light	42
The influence of laser surface texturing parameters on the surface of lean duplex stainless steel 2101 on microstructure and corrosion properties	42
Influence of fitting algorithms on thickness determination during monitoring of optical coatings	42
Water and oil repellent coating on fabric using hollow cathode PECVD	42
Effect of dilution on the properties of laser deposited AlCoCrFeNi high entropy alloy over SS316 substrate	42
Systematic optimization of Ag-perovskite SERS substrate fabrication via all-vacuum deposition for highly sensitive detection	42
The effect of Si addition in NbTiZr coatings	42
Ultrasonic pulsed waterjet peening of commercially-pure titanium	42

Morphology and yield of W nanoparticles in gas aggregation: Pathways towards functional nanocomposite films	42
Tribo-corrosion behavior of hypoeutectoid and hypereutectoid TC4-Cu coatings fabricated by laser surface alloying	42
Characteristics of droplet exudation on slippery liquid-infused porous surfaces considering thermal effect	41
H+/Cu2+ co-assisted corrosion synthesis of sustainable silicon dendrite anodes	41
Off-axis insertion of SiC particles in high-speed laser cladding of AlSi7Mg0.6	41
Chromium/nickel-free conversion coating as cold post-treatment to anodized AA2024-T3 for corrosion resistance increase	41
Research on the interface bonding mechanism and lifespan model of BIPV bonded structures	41
Influence of processing condition and post-spray heat treatment on the tribological performance of high velocity air-fuel sprayed Cr3C2-25NiCr coatings	41
Microstructure and wear behavior of invar alloy surface strengthened by TiAl laser alloying and TiCN ceramics	41
Effects of stoichiometry and substrate temperature on the mechanical properties of (Zr Ta1−)B films	40
Nanomechanical characterization of nanostructured Lu2SiO5 environmental barrier coatings by nano-indentation	40
Deposition of binary Cr Zr thin-film metallic glass using Cr/Zr dual-cathode high-power impulse magnetron sputtering	40
A sturdy PDMS-based multifunctional smooth coating with long-term corrosion resistance, anti-icing/deicing durability and self-cleaning performance	40
Ultrasonic surface rolling process for improving fatigue crack propagation resistance of laser-clad TC4-TA15 titanium alloy	40
Influence of cooling kinetics on surface texture, hydrophilicity and scratch resistance of the oxide layers produced by thermal oxidation on Ti-6Al-4V	40
Effect of heat treatment on the gas-atomized nickel‑aluminum bronze feedstock powders for cold spray	40
Understanding the multifunctional anticorrosion protective mechanism of epoxy-based coatings modified with hydrogel and benzotriazole conveying nanotubes for Q235 steel protection in 3.5 % NaCl	40
Influence of coating variables on the steam oxidation of modified silicon/ytterbium disilicate environmental barrier coatings	40
Chemical and mechanical performances of CVD‑silicon oxycarbonitride films for corrosion protection applications: Towards inert coatings in aggressive aqueous media	40
Effect of SiC gradient structure on ablation resistance of (Zr0.25Hf0.25Ti0.25Ta0.25)C multilayer coatings for C/C composites	40
The structure and properties of high-entropy (MoTaNbZrHf)-Si-B coatings deposited by DCMS and HIPIMS methods using the multilayer target	40
Study on the effect of acetate ions on the sealing treatment for anodic oxide film of 6063 aluminum alloy	39
Construction of biphasic FeCrAlW high entropy alloys coating of BCC and Al-rich FCC second phase for dual enhancement of strength and plasticity	39
The role of intermetallic compounds in mitigating liquid metal embrittlement in Al-Zn-Si coated steels	39
Effect of Ti3SiC2 concentration on corrosion resistance and ICR in bipolar plates composite ceramic coatings	39
A hBN/B-Si-Al-O-glass composite coating growth on SiCp/Al composite using one-step PEO with nanoparticle addition for outstanding electrical insulation performance	39
Sprayable superhydrophobic coating with high mechanical/chemical robustness and anti-corrosion	39
Oxidation behavior at 1100 °C of NiCrAlY coatings deposited by various PVD techniques	39
Enhanced wear resistance and surface properties of oxide film coating on biocompatible Ti45Nb alloy by anodization method	39
Structural optimization for the thermal conductivity and thermal cycling behavior in thermal barrier coatings and analysis of thermomechanical properties by computational investigation	39
Performance evaluation of CrAlN and TiAlN coatings deposited by HiPIMS in micro drilling of a Ni-based superalloy	39
Preparation of boron-doped diamond-like carbon films via enhanced-PECVD using an additional cathode	39
Hardness and tribological behaviour of annealed electroless nickel phosphorus composite layers with incorporated boron particles	38
Laser surface alloying of titanium alloy with silver: Microstructure, hardness and corrosion property	38
Influence of deposition pressure on the microstructure and mechanical properties of sputter-deposited MoNbTaW refractory multi-principal element alloy thin films	38
Electrical properties and thermistor behavior of TiAlN thin films deposited by combinatorial sputtering	38
Phase and microstructure evolutions of in-situ ZrC composite coating under plasma torch ablation	38
Atomic-scale investigation of the synergistic impact of Mo and Nb addition on enhancing the performance of laser cladding FeCoCrNi-based high entropy alloy coatings	38
Experimental characterization of the operation of modular cascade plasma torches	38
Superhydrophobic ultra-high molecular weight polyethylene porous material with self-cleaning ability, long-term stability, and high durability	38
Characterization of structural and mechanical properties of DLC films deposited on the surface of minute-scale 3D objects: Comparison of PECVD and FCVA deposition technique	38
Ni-based coating on 5083 aluminum alloy with Cu-Ni interlayer fabricated by ultra-high-speed laser directed energy deposition	38
Vickers hardness of NiW coating as a potential replacement for Cr-VI: A methodology to consider size effect and tip defect in classical microindentation	37
Effect of B4C-induced in-situ ceramic reinforcing phases on the mechanical properties of FeCoCrNiMnTi₀.₅Al₀.₅ high-entropy alloy coatings	37
Role of nitrogen doping on the structural evolution and properties of AlTiCrNbZrSiN high-entropy coatings	37
Excellent adhesion of protective α-Al2O3 layer formed on ODS FeCrAl alloys	37
Wear mechanism of a laser cladded Fe-based self-lubricating composite coating for protecting counter-abrasive parts	37
Dual protection against electrochemical corrosion for AA5083 Al alloys: Synergistic action of superhydrophobicity and strain-strengthening	37
Process optimization, microstructure characterization, and tribological performance of Y2O3 modified Ti6Al4V-WC gradient coating produced by laser cladding	37
Preparation of HT/PLA coatings on Zn-Mn-Mg alloy surface for biomaterials in bone tissue engineering	37
Role of oxygen plasma for improved preparation of Cu/CNT Nanohybrids by RF sputtering	37
Machine learning enabled the prediction of γ′-depleted depth during interdiffusion of bond-coated IN792 superalloy	37
Investigation of CMAS corrosion resistance for ZrO2-YTaO4 thermal barrier material at 1250 °C	37
Acetylated lignin as a biocomponent for epoxy coating — Anticorrosive performance analysis by accelerated corrosion tests	37
Investigation of Cu-doped amorphous carbon film in improving corrosion resistance and interfacial conductivity of proton exchange membrane fuel cell	37
Preparation of durable multi-functional coating silk fabrics with persistent fragrance release, antibacterial, fluoride-free superhydrophobic and self-cleaning properties	36
Tribological and mechanical behavior of tantalum and its compounds reinforced PEEK coatings for TKR	36
Effect of surface mechanical rolling pretreatment on microstructure and properties of nitrided TC4 titanium alloy	36
Dynamic evolution of temperature field, flow field, and solidification behavior during multilayer multitrack laser cladding	36
Annealing activated substrate element diffusion and its influence on the microstructure and mechanical properties of CVD TiN/TiCN coatings	36
Electrochemical behavior and anti-corrosion property of Ti3C2Tx MXene/LDH heterostructured coating on aluminum alloy	36
Optimizing laser cladding process parameters for transformation-induced plasticity FeMnCoCr high entropy alloy: A multi-objective approach	36
Influence of TiAl cathode material manufacturing route on the structural and tribo-mechanical properties of arc-evaporated TiAlN thin films	36
Effect of variable laser incident angles on microstructure and mechanical properties of laser-cladded Inconel 718	36
Effects of laser remelting on microstructure and tribological properties of plasma–sprayed Fe45Mn35Co10Cr10 high–entropy alloy coating	36
Friction and wear behaviors of Ta-based nanocrystalline composite coating under extreme sliding conditions	36
Effect of ultrasound assistance on the mechanical performance and corrosion resistance of Zn-Ni coatings produced by cathode plasma electrolysis deposition	36
High-temperature-driven degradation analysis and modelling of an industrial gas turbine applicable γ/β NiCoCrAlYRe coating – Part I: Microstructural investigations after long-term high-temperature exp	36
Plasma coloring of Ti via air atmospheric pressure plasma jet for dentistry	36
Unraveling the formation of enhanced long-term durability chromate-phosphate conversion coatings with a Cr(III) complex dye	36
Adhesion of cold sprayed soft coatings: Effect of substrate roughness and hardness	36
Electrochemical, mechanical, and tribological properties of corrosion product scales formed on X65 steel under CO2 supercritical pressure environments	36
Study of the electric arc dynamics in a cascaded-anode plasma torch	36
Research on corrosion behavior and biocompatibility of NiTi alloy processed with combined dealloying and annealing treatment	36
Effects of spraying parameters and heat treatment temperature on microstructure and properties of single-pass and single-layer cold-sprayed Cu coatings on Al alloy substrate	35
Yttrium-induced structural evolution and oxidation resistance in TiB2+∆ coatings deposited by conventional magnetron sputtering and HiPIMS	35
Synergistic effect of thermal annealing and metal–fatty acid coordination on the formation of superhydrophobic, corrosion-resistant surfaces	35
Magnetostriction and magnetic properties of sputtered Fe100-xMx (M = V and Cr) films	35
Electrochemical response and passivation affinity of Fe-based amorphous HVOF coatings prepared from pig iron on mild steel	35
An efficient salt-thermo-carburizing method to prepare titanium carbide coating	35
Understanding the thermal barrier performance of plasma-sprayed rare-earth zirconate coating against volcanic ash ingestion	35
Failure behaviour of EB-PVD YSZ thermal barrier coatings under simulated aero-engine operating conditions	35
Improvement of corrosion and wear resistances of 300M ultra high strength steel by low temperature cathode assisted plasma nitriding	35
Effect of laser remelting on the microstructure and phase composition of APS YAG coatings	35
Effect of different laser wavelengths on laser cladding of pure copper	35
Structural and tribological properties of sulfonitrocarburizing layers prepared by plasma nitrocarburizing and low temperature ion sulfurizing	35
Surface integrity engineering via ultrasonic surface rolling for enhanced hot salt stress corrosion cracking resistance of TC11 alloy	35
Core–shell NbTiC@M23C6 carbides embedded in an in-situ M2B network: A quasi-continuous protective architecture for laser-clad Fe-based composite coatings	35
Porous silica coating with excellent atomic oxygen protection performance and flexibility	35
Impact of shot peening on corrosion performance of AZ31 magnesium alloy coated by PEO: Comparison with conventional surface pre-treatments	35
Cold-sprayed novel Zn-Al-Ta ternary composite coating for corrosion resistance on magnesium alloy substrate	35
In-situ observation and directional growth of Ca2Lu8(SiO4)6O2 in Lu2SiO5 attacked by CMAS at 1500 °C	34
Effect of bias voltage on the tribocorrosion performance of TiAlSiN coatings on FH790 steel by arc ion plating	34
Potential of epoxy coating containing ionic liquid as anti-corrosion coating: Evaluation of barrier properties	34
Microstructure and properties of laser-cladded CoCrMoNb(TiC)x high entropy alloy coatings with various TiC contents	34