OOIR: Observatory of International Research

Papers

(The H4-Index of International Journal of Advanced Manufacturing Technology is 54. The table below lists those papers that are above that threshold based on CrossRef citation counts [max. 250 papers]. The publications cover those that have been published in the past four years, i.e., from 2021-11-01 to 2025-11-01.)

Article	Citations
A study of isothermal mechanical fatigue of welded reactor steel (15H2MFA)	281
Simulation of packaging design of virtual manufacturing products based on computer vision and Big data	251
Tribomechanical analysis and machining development for TiSiCN material deposited on industrial steel	209
Announcement of B. John Davies Prize for the best paper published in IJAMT in 2021	203
Towards robotic assembly: collision detection between each part of the parallel groove clamp	148
A monocular-based tracking framework for industrial augmented reality applications	148
Development of the production technology of a new highly effective thermal grease	146
An incremental flanging strategy for small hole with electropermanent magnetic device	136
Ladle pouring process parameter and quality estimation using Mask R-CNN and contrast-limited adaptive histogram equalisation	130
Tribological performance and corrosion resistance of HVOF WC-17 wt. % Co coatings: influence of micro-to-nanoscale morphology	127
Design and application of low-cost polymer composite shell and backfill tooling for stamping of HSS 590 sheets	126
On cutting forces considering elastic recovery accumulation in micro-milling process	126
Multi-objective parameter optimization of Ti6Al4V surface integrity for SEAM	124
Enhancing the bending strength of PEEK biomedical material welding parts using continuous drive friction welding with progressively increased welding area method	123
Development and implementation of a novel split-wise model to predict the cutting forces in milling of Al2024 for minimum error	108
Implementation of efficient surface discretisation algorithms adapted to geometric models specific to the footwear industry	106
Kriging quick adaptive sampling for multivariate optimization	103
In-process detection of miniature size holes in cold-rolled steel strips	100
Characterisation results for oxide ceramic functionally graded with cemented carbide sintered by PECS	94
Computational investigation of a novel metal thickness measurement system with coaxial triple-coil sensor for chemical mechanical polishing	94
Research on die-less spinning by spherical roller of different radius	90
A comparative machinability analysis of aged and freshly manufactured epoxy resins through orthogonal machining experiments	89
Precision dressing of arc-shaped coarse-grained diamond wheels via electrical discharge aided grinding technology	86
Finite element simulation and experimental study of non-blank holder forward and backward composite deep drawing earing test	83
Study on the hot stamping simulation and experiment of A-pillar patchwork blanks	82

Design and application of laser scanning strategy for machining deep surface grooves with a continuous-wave fiber laser	82
Experimental and numerical study of the CO2 laser-polishing edge effect on silica surface	78
Electromagnetic tube bulging due to axial pressure produced with a rigid drive block	77
Characterization and modelling of fracture in press-hardened Ductibor® 1000-AS:Usibor® 1500-AS laser-welded blanks	76
An inverse identification method for automatic estimation of heat source model parameters for laser directed energy deposition	75
Experimental investigations of tooth pitch variation and cutting parameters on areal surface texture in flat end milling of Fe–Ni alloy Supra50	75
Nanosecond- and picosecond-pulsed laser cutting of lithium metal anodes with copper current collector	72
Material removal characteristics of small-size polyurethane polishing wheel	71
Study on surface quality in spray-mist-assisted laser processing of tungsten carbide cobalt	70
Numerical prediction of AISI D2 punch damage	68
Correction to: Influence of the scale effect on the constraint effect in welded joints with soft interlayers	67
Correction to: Cutting chatter recognition based on spectrum characteristics and extreme gradient boosting	66
An on-line contour error estimation and compensation strategy for five-axis local smoothed trajectory under motion time synchronization	64
Investigation on the machinability of metastable β titanium alloy M28	62
Effect of chamfer width and chamfer angle on tool wear in slot milling	62
Theoretical and experimental study on influencing factors of rabbit ear in the gear forced throughfeed rolling process	62
Surface integrity enhancement of LA103Z Mg-Li alloy by regulating microstructure and texture evolution in cutting metamorphic layer	60
Tool wear monitoring in microdrilling through the fusion of features obtained from acoustic and vibration signals	60
Correction to: Comparison of the deformation behavior of circular hole‑flanging obtained by electromagnetic forming and stamping	59
Correction to: Scanning strategies for the 316L part with lattice structures fabricated by selective laser melting	59
A study on porosity and mechanical properties of the open aluminum metal foam through spark plasma sintering SDP technique	58
Effects of laser process parameters on the hardness profile of AISI 4340 cylindrical samples: statistical and experimental analyses	58
Research on ultrasonic longitudinal-torsional shank based on the giant magnetostrictive material	58
Design of VHF micro-EDM discharge state detection method based on energy coupling detection	57
The effect of semi-cured elements on the quality of integrated composite structures	56
Laser surface texturing-based hybrid micro-milling of Ti6Al4V alloy	56
Study on the heat input regulation mechanism of compound excitation device and its influence on arc shape and penetration behavior in GTAW	55
Mobile rack AS/RS dimensions optimization for single cycle time minimization	54
Experimental study on corner filling of B1800HS boron steel tubes in hot metal gas forming process	54
Research on automatic analysis and layout system of the stamping process for automotive panels and its key technologies	54
Computerized image analysis in manufacturing industry anomaly detection using artificial intelligence techniques	54
The generation of supplementary toolpaths for surface machining based on rapid prediction of scallop height distributions	54
Effects of post-weld heat treatments in microstructure, mechanical properties, and corrosion resistance of simulated heat-affected zone of supermartensitic steel UNS S41426	54