OOIR: Observatory of International Research

Papers

(The TQCC of Transaction of the Canadian Society for Mechanical Engineering is 3. The table below lists those papers that are above that threshold based on CrossRef citation counts [max. 250 papers]. The publications cover those that have been published in the past four years, i.e., from 2022-06-01 to 2026-06-01.)

Article	Citations
Residual life prediction of aluminum alloy plates under cyclic loading using an integrated prognosis method	29
Thermal fatigue damage assessment of high-speed train brake discs under multiple braking conditions	20
Effects of biodiesel ratio and nozzle diameter on combustion and emissions of a biodiesel–DME-fueled engine	13
Dynamic characteristics analysis of rotary coupled controller in directional well	12
Structural Design and Intelligent Control of a Self-Reconfigurable Robot for Space Cabins	11
Numerical investigation of the effect of hole reaming on fatigue life by cold expansion	11
Fatigue analysis of selective laser melting Inconel 718 and the mechanism of ductile–brittle continuous alternating steps during fatigue process	10
Logic design method and optimization of hydraulic system for heavy-duty automatic transmission	10
Influence of different combinations of high-order topological modification on contact pattern and load distribution of helical gear	10
A hierarchical search-based method for extracting boundary feature lines of aircraft skin	9
Numerical study of flow patterns and performance of a coupled cavity–dish system under different focal lengths	8
Research on reducing flow shock of the digital hydraulic wind turbine	8
Semi-analytical modeling and thermomechanical coupling vibration analysis of hard-coating thin-walled cylindrical shell under thermal environments and arbitrary boundary conditions	7
Meshing characteristics analysis of involute helical gear drive based on the semi-analytical method	7
Adaptive robust control for the corner balancing Cubli system with uncertainties	7
Research on optimal fast terminal sliding mode control of horizontal vibration of high-speed elevator car system	7
Low-cost two-dimensional digital image correlation system	6
Study on multibody contact load distribution characteristics of scraper conveying system of continuous miner	6
A comparison of four machine learning techniques and continuous wavelet transform approach for detection and classification of tool breakage during milling process	6
Speed control strategy for power line inspection robot servo system considering time-varying parameters	6
Comparison of flow and loss aspects in the rotors of a counter-rotating turbine	6
Dynamic and thermal coupling modeling analysis of full-ceramic angular contact ball bearing considering sliding	6
Larger trabecular bone structural units (BSU) can slow crack growth in idealized 2D extended finite element method (XFEM) models by delaying when the crack tip reaches the cement line	6
Design of ABS fuzzy sliding mode control system based on pavement recognition	5
Design, modeling, and simulation of a novel transducer for vibration energy recovery system of speed bump	5

Investigation of high-speed impact on plates by magnetic pulse	5
Magnetic circuit design of MR controller for improving the performance of the suspension	5
Design and application of a fault diagnosis system for machine tool angle heads based on Boolean matrix filtering and an optimized BP neural network	5
Data-driven traction characteristics modeling and prediction of agricultural tractor transmission systems using Physics-informed Neural Network approach	5
Thermal mixed elastohydrodynamic lubrication analysis of involute helical gears with surface roughness	5
Improved multi-objective coati optimization algorithm for trajectory planning of robotic manipulators	5
Analysis of the enhanced effect of modulation of monotonic magnetic ring double-modulated three-rotor coaxial magnetic gear and its multi-objective optimization	5
Collaborative control of circumferential yarn implantation system for large-scale 3D braiding equipment using fast nonsingular terminal sliding mode	5
Band gap generation in cantilever beams through periodic material removal	5
Predicting the kinematic response of a helmeted headform during oblique impacts	5
Torque prediction in ultrasonic vibration assisted drilling for small and deep holes using AI	5
Note of appreciation	4
Nonlinear Vibration Analysis of Bearing with Coupled Ball and Outer Ring Raceway Defects	4
Mechanical grouting sleeve of rebars: experimental investigations	4
Flow force analysis and optimization of lock valve for heavy-duty automatic transmission	4
Milling characteristics of SiCp/2024Al composites thin-walled part based on movable auxiliary support	4
Distributed electric vehicle decoupling control based on GA-BP neural network	4
Internal cooling system effects to heat transfer and tool wear in turning operations of titanium alloys Ti6Al4V	4
Trajectory study of power inspection quadcopter based on Udwadia–Kalaba theory	4
Dynamic characteristics of a relief valve captured by a combination of fluid–solid coupling and feedforward neural network (FNN)	4
Key design parameters optimization and joint control of double throttling pipe air damping spring	4
Numerical investigation of fluid flow and heat characteristics of a roughened solar air heater with novel V-shaped ribs	4
Aerodynamic performance analysis of a supercritical airfoil in the helicopter main rotor	4
Design and validation of an MRI conditional surgical robot for neurosurgery with remote center-of-motion	4
The effects of nanoparticles as a biodiesel ingredient on the performance of a VCR diesel engine	4
Hybrid ray-tracing model for solar energy assessment and its open-source implementation as a service	4
Non-pneumatic tire–road interaction: a tractive effort analysis	4
Dynamic characteristics of electromechanical coupling of body-suspended drive system for high-speed trains under wheel polygonal wear	4
Characteristics analysis and nonlinear control of a digital hydraulic pressure tracking system for high-speed helicopter wet friction clutch	3
Characterization of a manual gas tungsten arc weld overlay using Inconel 686	3
Design and analysis of a novel rotary inertance hydraulic converter with the continuous controlling turntable	3
Nonsingular fast terminal sliding mode control for robotic manipulators: a synergistic approach integrating RBFNN and AESO	3
An innovative design of INVELOX wind turbine: a numerical study on the effects of implementing long flange and Venturi holes	3
On modelling the cutting forces and impact resistance of honed milling tools	3
Thermal analysis of a stator oil-immersed cooling high-speed permanent magnet generator based on the lumped parameter thermal network method	3
Bronze wool as a porous mixer for air temperature uniformity in energy exchangers	3
Note of appreciation	3
Microneedle arrays for brain drug delivery: the potential of additive manufacturing	3
On the simulation of a wing with detached end-plates using an actuator line based on an anisotropic Gaussian kernel	3
Evaluating roof-mounted VAWT performance with CFD for various building shapes, boundary layer flows, and location scenarios	3
Design and dynamic characteristics of automatic vertical drilling tool	3
Feature selection and framework design toward data-driven predictive sustainability assessment and optimization for additive manufacturing	3
Ultimate strength analysis of pitted plates with transverse cracks	3
Tribological performance analysis of Stellite and Cr ₃ C ₂ coatings on Inconel 625	3
Probabilistic assessment of exergy analysis of a wind turbine for optimum performance	3
Nonlinear control strategies for UAV navigation in complex terrains: a constraint-based approach for robust obstacle avoidance and mission efficiency	3
Global curvature characteristics analysis of offset ZI worm drive	3
Combine harvester assembly fault diagnosis based on optimized multi-scale reverse discrete entropy	3
Thermodynamic performance of an ejector–compressor enhanced diffusion–absorption refrigeration system for cement kiln waste heat recovery	3
Multi-objective optimization design for the table of a CNC machine tool based on bionic structures	3

Influence of dynamic change of radial clearance on flow and thermal characteristics of full ceramic angular contact ball bearing	3
Data-driven reduced-order models for transient temperature fields using dynamic mode decomposition	3
Bearing Fault Diagnosis Using Domain Adaptation Approach for Acoustic Data	3
Signal-to-noise ratio analysis on saw-tooth vortex generator in vehicle radiators	3
Effect of non-Gaussian roughness tooth surface on lubrication state of grease lubricated spiral bevel gear under mixed-thermal elastohydrodynamic effect	3
Performance analysis of vibration characteristics on VCR engine using hybrid honeycomb structure	3
A model for permeability in fibre-reinforced plastics	3