OOIR: Observatory of International Research

Papers

(The TQCC of Journal of Polymer Engineering is 3. The table below lists those papers that are above that threshold based on CrossRef citation counts [max. 250 papers]. The publications cover those that have been published in the past four years, i.e., from 2020-05-01 to 2024-05-01.)

Article	Citations
Polysulfone nanofiltration membranes enriched with functionalized graphene oxide for dye removal from wastewater	43
Research progress of low dielectric constant polymer materials	39
Research and application progress of lignin-based composite membrane	33
A review on 3D printing in tissue engineering applications	32
Swelling behavior and mechanical properties of Chitosan-Poly(N-vinyl-pyrrolidone) hydrogels	29
Antimicrobial magnetic poly(GMA) microparticles: synthesis, characterization and lysozyme immobilization	23
Removal of 17β-estradiol from aqueous systems with hydrophobic microspheres	23
Development and characterization of ethyl cellulose nanosponges for sustained release of brigatinib for the treatment of non-small cell lung cancer	23
Effect of blending procedures and reactive compatibilizers on the properties of biodegradable poly(butylene adipate-co-terephthalate)/poly(lactic acid) blends	22
Effectiveness assessment of TiO₂-Al₂O₃ nano-mixture as a filler material for improvement of packaging performance of PLA nanocomposite films	21
Investigating the relationship between tack and degree of conversion in DGEBA-based epoxy resin cured with dicyandiamide and diuron	20
Simvastatin-loaded graphene oxide embedded in polycaprolactone-polyurethane nanofibers for bone tissue engineering applications	18
Advancement in hemp fibre polymer composites: a comprehensive review	18
A review on tribo-mechanical properties of micro- and nanoparticulate-filled nylon composites	17
Use of virgin/recycled polyethylene blends in rotational moulding	17
Effects of talc, kaolin and calcium carbonate as fillers in biopolymer packaging materials	17
Roll-over-web coating analysis of micropolar-Casson fluid: a theoretical investigation	16
Mathematical analysis of a non-Newtonian polymer in the forward roll coating process	14
Fabrication and charge storage capacitance of PPY/TiO₂/PPY jacket nanotube array	14
Non-isothermal blade coating analysis of viscous fluid with temperature-dependent viscosity using lubrication approximation theory	13
Asphalt concrete based on a polymer–bitumen binder nanomodified with carbon nanotubes for road and airfield construction	12
Effect of infill density and pattern on the specific load capacity of FDM 3D-printed PLA multi-layer sandwich	11
Water-soluble polymeric particle embedded cryogels: Synthesis, characterisation and adsorption of haemoglobin	11
Determination of mechanical properties of two-phase and hybrid nanocomposites: experimental determination and multiscale modeling	11
Elaboration and characterization of multilayer polymeric membranes: effect of the chemical nature of polymers	10

Simultaneous improvement of mechanical and conductive properties of poly(amide-imide) composites using carbon nano-materials with different morphologies	10
Effect of nanodiamond particles on the structure, mechanical, and thermal properties of polymer embedded ND/PMMA composites	10
Effect of gamma radiation on the structural, thermal and optical properties of PMMA/Sn_0.75Fe_0.25S₂ nanocomposite	10
Thermal and mechanical behavior of SBR/devulcanized waste tire rubber blends using mechano–chemical and microwave methods	9
Changes in the morphology, mechanical strength and biocompatibility of polymer and metal/polymer fabricated hydroxyapatite for orthopaedic implants: a review	9
The effect of cooling rate on crystallization behavior and tensile properties of CF/PEEK composites	9
Novel alginate immobilized TiO₂ reusable functional hydrogel beads with high photocatalytic removal of dye pollutions	9
A review of the thermal storage of phase change material, morphology, synthesis methods, characterization, and applications of microencapsulated phase change material	9
Green composites based on Atriplex halimus fibers and PLA matrix	9
PVA coating of ferrite nanoparticles triggers pH-responsive release of 5-fluorouracil in cancer cells	8
Synthesis of Ag@PANI nanocomposites by complexation method and their application as label-free chemo-probe for detection of mercury ions	8
Effects of infill pattern and density on wear performance of FDM-printed acrylonitrile-butadiene-styrene parts	8
Rheological and thermal stability of interpenetrating polymer network hydrogel based on polyacrylamide/hydroxypropyl guar reinforced with graphene oxide for application in oil recovery	8
Microcellular foaming behavior of ether- and ester-based TPUs blown with supercritical CO₂	8
Influences of interface structure on tribological properties of engineering polymer blends: a review	7
Flexible silicone rubber/carbon fiber/nano-diamond composites with enhanced thermal conductivity via reducing the interface thermal resistance	7
Thermal stability, mechanical properties, and gamma radiation shielding performance of polyvinyl chloride/Pb(NO₃)₂ composites	7
Assessment of processibility and properties of raw post-consumer waste polyethylene in the rotational moulding process	7
Boron nitride nanoplatelets as two-dimensional thermal fillers in epoxy composites: new scenarios at very low filler loadings	7
Approach to quantify the resistance of polymeric foams against thermal load under compression	7
Formulating calcium carbonate masterbatches	7
Effect of new metal–organic framework (zeolitic imidazolate framework [ZIF-12]) in mixed matrix membranes on structure, morphology, and gas separation properties	7
Computational prediction of electrical percolation threshold in polymer/graphene-based nanocomposites with finite element method	6
The effects of ZnO nanoparticle reinforcement on thermostability, mechanical, and optical properties of the biodegradable PBAT film	6
Polypropylene hybrid composites: Effect of reinforcement of sisal and carbon fibre on mechanical, thermal and morphological properties	6
Invertase adsorption with polymers functionalized by aspartic acid	6
A functionalized tannin-chitosan bentonite composite with superior adsorption capacity for Cr(VI)	6
Additive manufactured parts produced by selective laser sintering technology: porosity formation mechanisms	6
Enhancing performances of hemp fiber/natural rubber composites via polyhydric hyperbranched polyester	6
Continuous reactors of frontal polymerization in flow for the synthesis of polyacrylamide hydrogels with prescribed properties	6
An environmentally sustainable isosorbide-based plasticizer for biodegradable poly(butylene succinate)	5
Effects and mechanism of filler content on thermal conductivity of composites: a case study on plasticized polyvinyl chloride/graphite composites	5
Design criteria for the pin-foot ratio for joining adhesion-incompatible polymers using pin-like structures in vibration welding process	5
Comparative study of conventional and microwave heating of polyacrylonitrile-based fibres	5
Mechanical and wear behaviour of PEEK, PTFE and PU: review and experimental study	5
Maghnite: an innovative inorganic reinforcement utilized in the synthesis of polyamide 12 nanocomposites with optimized thermal and mechanical properties	5
Effects of gas-assisted extrusion on slip in the cable coating process	5
Mechanical and antibacterial properties of ZnO/chitosan bio-composite films	5
Preparation and characteristics of sepiolite-waterborne polyurethane composites	5
Polyurethane modified epoxy vitrimer and its stress relaxation behavior	5
Improving the rheological properties of water-based calcium bentonite drilling fluids using water-soluble polymers in high temperature applications	5
Application of the polycaprolactone polymer for the encapsulation of geraniol: evaluation of the efficiency and stability	5
Network structural hardening of polypropylene matrix using hybrid of 0D, 1D and 2D carbon-ceramic nanoparticles with enhanced mechanical and thermomechanical properties	4
Tribological properties of organotin compound modified UHMWPE	4
Kinetic study of the pyrolysis of polypropylene over natural clay	4
Design and characterization of ramie fiber-reinforced composites with flame retardant surface layer including iron oxide and expandable graphite	4
A brief review on polymer nanocomposites: current trends and prospects	4
Bilayer PMMA antireflective coatings via microphase separation and MAPLE	4
Development and characterization of eco-friendly biopolymer gellan gum based electrolyte for electrochemical application	4
Investigation of morphology and transport properties of Na⁺ ion conducting PMMA:PEO hybrid polymer electrolyte	4

The effect of fibre surface treatment and coupling agents to improve the performance of natural fibres in PLA composites	4
Quality prediction and control of thin-walled shell injection molding based on GWO-PSO, ACO-BP, and NSGA-II	4
Morphology optimization of poly(ethylene terephthalate)/polyamide blends compatibilized via extension-dominated twin-screw extrusion	4
Recent progress on improving the mechanical, thermal and electrical conductivity properties of polyimide matrix composites from nanofillers perspective for technological applications	4
Influence of fabrication parameters on the elastic modulus and characteristic stresses in 3D printed PLA samples produced via fused deposition modelling technique	4
Study on the thermal insulation performance of the core–shell skeleton graphene oxide/carbon composite aerogel	4
Investigations of the characteristics and performance of modified polyethersulfones (PES) as membrane oxygenator	4
Ramie fiber reinforced composites with flame retardant structure design: flammability, smoke suppression, and mechanical properties	4
Water purification performance enhancement of PVC ultrafiltration membrane modified with tourmaline particles	4
Nano-SiO₂/hydroxyethyl cellulose nanocomposite used for 210 °C sedimentation control of petroleum drilling fluid	4
Fire-retardant wood coating based on natural rubber bearing methacrylic functionality	4
In situ prepared composite of polypyrrole and multi-walled carbon nanotubes grafted with sodium polystyrenesulfonate as ammonia gas sensor with wide detection range	4
Variation in final sheet thickness in case of Sutterby fluid during the calendering process	4
Preparation of hydrophilic modified polyvinylidene fluoride (PVDF) ultrafiltration membranes by polymer/non-solvent co-induced phase separation: effect of coagulation bath temperature	3
Dual effect of maleic anhydride and gamma radiation on properties of EPDM/microcrystalline newsprint fiber composites	3
Effect of antiblock and slip additives on the properties of tubular quenched polypropylene film	3
Miscible blend polyethersulfone/polyimide asymmetric membrane crosslinked with 1,3-diaminopropane for hydrogen separation	3
Study on bubble morphology at interface of laser direct joint between carbon fiber reinforced thermoplastic (CFRTP) and titanium alloy	3
Star-shaped arylacetylene resins derived from silicon	3
Process optimization for extraction of avian eggshell membrane derived collagen for tissue engineering applications	3
Mechanical and flammability properties of a polyamide 6,6 nanocomposite for nonstructural marine engine components	3
Study of effect of wood-flour content on mechanical, thermal, rheological properties and thermoformability of wood-polypropylene composites	3
Characterization of polymeric biomedical balloon: physical and mechanical properties	3
Preparation and swelling behavior of end-linked hydrogels prepared from linear poly(ethylene glycol) and dendrimer-star polymers	3
Production of elastomer-based highly conductive hybrid nanocomposites and treatment with sulfuric acid	3
Influence of extrusion screw speed on the properties of halloysite nanotube impregnated polylactic acid nanocomposites	3
Doubly modified MWCNTs embedded in polyethersulfone (PES) ultrafiltration membrane and its anti-fouling performance	3
Numerical investigation of tubular expansion and swelling elastomers in oil wells	3
Characterisation of melamine formaldehyde microspheres synthesised with prolonged microencapsulated reaction time	3
Fabrication of ultrahigh-molecular-weight polyethylene porous implant for bone application	3
Study on the interface morphology in the induction welding joint of PEEK plate at low power	3
Lignin reinforced, water resistant, and biodegradable cassava starch/PBAT sandwich composite pieces	3
Fabrication of poly (1, 8-octanediol-co-Pluronic F127 citrate)/chitin nanofibril/bioactive glass (POFC/ChiNF/BG) porous scaffold via directional-freeze-casting	3
The effects of morphological variation and polymer/polymer interface on the tensile modulus of binary polymer blends: a modeling approach	3
Characterization of polypropylene/magnesium oxide/vapor-grown carbon fiber composites prepared by melt compounding	3
Microstructure and improvement in corrosion resistance of HAP and PVA/HAP	3
Investigation of optical and biocompatible properties of polyethylene glycol-aspirin loaded commercial pure titanium for cardiovascular device applications	3
Improving dispersive mixing in compatibilized polystyrene/polyamide-6 blends via extension-dominated reactive single-screw extrusion	3
Pyrolysis and combustion of polystyrene composites based on graphene oxide functionalized with 3-(methacryloyloxy)-propyltrimethoxysilane	3
Experimental investigations on compressive, impact and prediction of stress-strain of fly ash-geopolymer and portland cement concrete	3
An environment friendly hemp fiber modified with phytic acid for enhancing fire safety of automobile parts	3
A quantitative study on using digital photoelasticity for characterising the effect of the stretching speed on the necking phenomenon	3
In vitro biocompatibility study of microwave absorbing conducting polymer blend films for biomedical applications	3
Effect of pro-oxidant concentration on characteristics of packaging films of cobalt stearate filled polypropylene	3