Chinese Journal of Mechanical Engineering

Papers
(The TQCC of Chinese Journal of Mechanical Engineering is 15. The table below lists those papers that are above that threshold based on CrossRef citation counts [max. 250 papers]. The publications cover those that have been published in the past four years, i.e., from 2021-11-01 to 2025-11-01.)
ArticleCitations
Development and Control of a Magnetorheological Damper-Based Brake Pedal Simulator for Vehicle Brake-by-Wire Systems147
MPC-Based Coordinated Control of Gear Shifting Process for a Power-split Hybrid Electric Bus with a Clutchless AMT104
Subsurface Defect Evaluation of Selective-Laser-Melted Inconel 738LC Alloy Using Eddy Current Testing for Additive/Subtractive Hybrid Manufacturing93
Automatic Bone Surface Restoration for Markerless Computer-Assisted Orthopaedic Surgery85
Tooth Position and Deformation of Flexspline Assembled with Cam in Harmonic Drive Based on Force Analysis81
Rail Roughness Acceptance Criterion Based on Metro Interior Noise78
Cutting Behavior of Cortical Bone in Different Bone Osteon Cutting Angles and Depths of Cut67
Integrated Optimization of Structure and Control Parameters for the Height Control System of a Vertical Spindle Cotton Picker63
Improved Dynamics Model of Locomotive Traction Motor with Elasticity of Rotor Shaft and Supporting Bearings57
Design of Passive Constant-Force End-Effector for Robotic Polishing of Optical Reflective Mirrors57
Target Vehicle Selection Algorithm for Adaptive Cruise Control Based on Lane-changing Intention of Preceding Vehicle53
Research Progress of Refractory High Entropy Alloys: A Review51
Formation Principle and Characteristics of Self-Supercharging Pulsed Water Jet49
Design and Experimental Study of Pressure Compensation System for Full-Ocean-Depth Gas-Tight Sediment Sampler47
Dynamic Accuracy Analysis of a 5PSS/UPU Parallel Mechanism Based on Rigid-Flexible Coupled Modeling46
Development of a Wearable Upper Limb Rehabilitation Robot Based on Reinforced Soft Pneumatic Actuators43
Three-dimensional Modeling and Simulation of Muscle Tissue Puncture Process39
Velocity Constraints Based Approach for Online Trajectory Planning of High-Speed Parallel Robots39
Statistical Analyses of the Strengths of Particulate Reinforced Metal Matrix Composites (PRMMCs) Subjected to Multiple Tensile and Shear Stresses38
Numerical Study on Effect of Non-uniform CMAS Penetration on TGO Growth and Interface Stress Behavior of APS TBCs36
Tribological Properties of Cylinder Block/Valve Plate Interface of Axial Piston Pump on the Tribometer31
Dynamic Finite Element Modeling and Simulation of Soft Robots30
Tire Road Friction Coefficient Estimation: Review and Research Perspectives28
Application of Optimal-Jerk Trajectory Planning in Gait-balance Training Robot27
Synchronization and Stability of a Nonlinear Vibrating Mechanical System Characterized by Asymmetrical Piecewise Linearity23
Lifetime and Aging Degradation Prognostics for Lithium-ion Battery Packs Based on a Cell to Pack Method22
Morphological Heredity of Intermetallic Nb5Si3 Dendrites in Hypereutectic Nb-Si Based Alloys via Non-Equilibrium Solidification22
Uncertainty Analysis and Optimization of Quasi-Zero Stiffness Air Suspension Based on Polynomial Chaos Method21
Greentelligence: Smart Manufacturing for a Greener Future21
A Review of Nano/Micro/Milli Needles Fabrications for Biomedical Engineering21
Precision and Flexible Bending Control Strategy Based on Analytical Models and Data Models21
Prediction and Minimization of the Heat Treatment Induced Distortion in 8620H Steel Gear: Simulation and Experimental Verification19
Resolution Enhancement in Ultrasonic TOFD Imaging by Combining Sparse Deconvolution and Synthetic Aperture Focusing Technique (Sparse-SAFT)19
Ultrasonically Assisted Cutting of Histological Sections for  Reducing the Environmental and Financial Impact of Microtomy19
Optics-guided Robotic System for Dental Implant Surgery19
Wheel Setting Error Modeling and Compensation for Arc Envelope Grinding of Large-Aperture Aspherical Optics19
Competitive Failure of Bolt Loosening and Fatigue under Different Preloads18
Novel Ring Compression Test Method to Determine the Stress-Strain Relations and Mechanical Properties of Metallic Materials18
Optimization Transmission Efficiency with Driver Intention for Automotive Continuously Variable Transmission under Slip Mode18
Modeling and Parameter Sensitivity Analysis of Valve-Controlled Helical Hydraulic Rotary Actuator System18
Improved Multi-Bandwidth Mode Manifold for Enhanced Bearing Fault Diagnosis17
Inverse Dynamics of A 3-DOF Parallel Mechanism Based on Analytical Forward Kinematics17
Motion Characteristics Analysis of a Novel Spherical Two-degree-of-freedom Parallel Mechanism17
Workspace and Accuracy Analysis on a Novel 6-UCU Bone-attached Parallel Manipulator17
Wire Arc Additive Manufactured CuMn13Al7 High-Manganese Aluminium Bronze16
Hybrid Navigation System Based Autonomous Positioning and Path Planning for Mobile Robots16
A Type-2 Fuzzy Approach to Driver-Automation Shared Driving Lane Keeping Control of Semi-Autonomous Vehicles Under Imprecise Premise Variable16
Recent Advances in Processing of Biological Tissues15
Gas Leakage Detection and Pressure Difference Identification by Asymmetric Differential Pressure Method15
The Effect of Laser Ablation Pulse Width and Feed Speed on Necrosis and Surface Damage of Cortical Bone15
Formation Mechanism of Precursor Films at High Temperatures: A Review15
0.094924926757812