OOIR: Observatory of International Research

Papers

(The TQCC of Materials Science is 4. The table below lists those papers that are above that threshold based on CrossRef citation counts [max. 250 papers]. The publications cover those that have been published in the past four years, i.e., from 2022-05-01 to 2026-05-01.)

Article	Citations
Indirect Evaluation of the Thickness of Coatings on Synthetic-Diamond Powders with the Use of New 3D Grain Models	33
Structure and Properties of Polyester Composites with Polymer Silicate Modifier	23
Evaluation of the increased local trapped hydrogen concentration	21
Evolution of nonmetallic inclusions during hot rolling of steels	19
The Influence of Corrosion Dissolution of the Metal Surface Layer on the Stress Concentration Factor in Butt-Welded Joins	18
Mechanical and Corrosion Properties of Fe–B–C Alloys	18
Vibration Analysis of the Damaged Bearing Unit of the Port Crane Lifting Mechanism	16
Effect of Laser Surface Treatment on the Initiation of Corrosion Defects near Nonmetallic Inclusions	15
Corrosion Inhibition of Low-Alloy Steel by a Composite Pigment Based on Zeolite and Monocalcium Phosphate	14
Generation of Hydrogen by the Hydrolysis of Mixtures of Magnesium Hydride with Citric Acid	14
Gum Arabic as an Environmentally Friendly Inhibitor for Corrosion Protection of 09G2S Steel in Neutral Media	13
Complex modification of heat-resistant ZhS3DK-VI alloy with yttrium and titanium carbonitride	13
Regularities and mechanism of the anti-corrosion action of “green” inhibitors in neutral aqueous environments	13
Wear resistance and fracture of low-alloyed steel when moving in abrasive plant mass	12
Use of Polyols of Petroleum Chemical Processing as Raw Materials for the Synthesis of Polyurethanes	12
Specific Features of Change of the Plate Shape During the Formation of Gradient Alloys of Palladium With Hydrogen	12
The influence of titanium pre-nitriding on the synthesis of oxide-ceramic coatings	12
Corrosion-Mechanical Properties and Susceptibility to Hydrogenetaion of Pipe Steel in the Presence of Carbon Dioxide Gas and Hydrogen Sulphide in Environment	12
Thermodeformed state of the aluminum plate during induction heat treatment	11
Determination of thermal stress state of cylindrical bodies with multilayer inhomogeneous coatings	11
Torsion crack in a piecewise homogeneous body with a thin layer at the interface	10
Dynamic forces in a carrying rope with supports at different levels during an instantaneous change of the technological load	10
Long-term oxidation resistance and electrical conductivity of materials in the cathode and anode environments of fuel cells	9
Substantiation of modes of restorative heat treatment of heat-resistant steel of TPP steam pipeline bend	9
Method for Checking the Cyclicity of the Microrelief of the Titanium Alloy Self-Organized Laser-Treated Surface	9

Physicomechanical properties of arc sprayed coating formed in supersonic mode	9
Investigation of the compression of a piecewise homogeneous half-plane with a fixed boundary along the interface crack	9
Modeling of Pitting of Heat Exchangers Made of 18/10 Type Steel in Circulating Waters	8
Composite ScCeSZ–YSZ ceramics for solid oxide fuel cell electrolyte	8
Calculation of Stresses in Composite Strips with Cracks on the Base of Modified Integral Equations Taking into Account the Contact of their Edges	8
Structure, modulus of elasticity, and corrosion resistance of Ti–20Nb–20Zr alloy	8
Specific features of double-differentiation eddy current probe signals from inclined cracks	8
Change of Microstructure and Properties of WC–Co Cemented Carbides as a Result of High Pressure and Temperature	8
Pulse-Arc Surfacing of Corrosion-Resistant Austenitic-Martensitic Steel	8
Development of the Laboratory Method of Degradation of Steels for the Evaluation of their Resistance to Corrosion Cracking	7
The Influence of the Electrolyte Composition for Hard Anodizing of Aluminum on Corrosion Resistance of Synthesized Coatings	7
Assessment of wear of contact surfaces of cams and rollers of press drive mechanisms under cyclic loading	7
Evaluation of the Endurance Limit of Cooled Blades of Gas-Turbine Engines Made of Heat-Resistant Nickel Alloy	7
Evaluation of the Residual Life Time of the Ethylene Production Rectification Column Under Wind Load and Atmospheric Corrosion	7
Nickel-containing composite material for electromagnetic radiation shielding	7
Evaluation of the mechanical properties of the high-temperature area in the heat-affected zone during deposition of a difficult-to-weld nickel-based superalloy	7
Assessment of the residual life of railway rail with surface cracks	7
Influence of Hydrogen Peroxide on the Composition and Porosity of Oxide-Ceramic Coatings on Alloys of the Al–Si–Cu and Al–Cu–Mg Systems	7
Heat Resistance of Zr–1Nb Alloy Claddings in Water Vapor after Ion-Plasma Nitriding	7
Modeling of the Influence of Hydrogen on the Deformation of Metals	7
Anti-corrosion properties of composite inhibiting pigment based on natural calcium silicate and zinc orthophosphate in epoxy coating on aluminum alloy	7
Influence of hydrogen charging parameters on the strength of 60S2A steel	6
Effect of Zeolite-Phosphate Anti-Corrosion Pigment on Protective Properties of Epoxy Coating on Carbon Steel	6
Evaluation of Residual Stresses during Mechanical Treatment of Machine Parts	6
Mathematical Prediction of the Properties of Heat-Resistant Nickel Alloys After Directional Crystallization	6
Nonlinear elastic behavior and effective parameters of materials with pores and flaw-like defects	6
Corrosion inhibition of D16T aluminum alloy by sodium alginate and zinc acetate composition in neutral chloride-containing environment	6
Induction Zone Sintering of WC–8Co Hard Alloy	6
Stress State of an Orthotropic Plate at the Holes with Sharp and Rounded Tips	6
Mechanical and magnetic properties of biocomposites based on hydroxyapatite modified by magnetite and chitosan	6
Energy Aspects of Tribosystems	6
Indicator of the crack growth resistance as one of the factors for the express analysis of damaged pipelines	6
Prediction of Fill Factor and Charge Density of Self-Shielding Flux-Cored Wire with Variable Composition	6
Radar Method for the Remote Monitoring of the Corrosion State of Reinforced-Concrete Structures	6
The influence of the structural-mechanical state of the gas transit pipeline steel on the susceptibility to hydrogen embrittlement	6
Comparative Study of Corrosion Activity of Bright and Matte Nickel Coatings in Solutions and Vapor of Acetic Acid	6
Phase composition, structure, and properties of electrospark coating on titanium	6
Specific Features of Corrosion of Heating Network Pipelines Made of 17G1S Steel	6
Structure and properties of the high-entropy TiCrFeNiGa alloy	6
Morphology and Physicomechanical Properties of Modified Polyamides	6
The Influence of Different Factors on Physicomechanical Properties of High Entropy Alloys with fcc Lattice	5
The effect of ferrochrome content in the initial charge on the structure, mechanical and tribotechnical properties of Fe–Cr–C sintered carbide steel	5
Study of the influence of the MasterSure HES 1515 polycarboxylate-type superplasticizer on the physicomechanical properties of high-strength concretes	5
Acoustic-Emission Method of Determining Residual Life of Thin-Walled Structural Elements Under the Action of Force Loads and Corrosive Environments	5
Thermodynamic analysis of the formation of chemical compounds reactions during arc spraying of coatings with cored wires	5
Calculation of Fuel Rod Strength Under Steady-State Operating Condition	5
Influence of surface nanostructure alloying on ShKh15 steel contact fatigue	5
Assessing of the Life Time of a Shaft with a Crack in Hydrogen	5
Electrochemical charge-discharge characteristics of RMgNi3.5Mn0.5 alloys	5
High-temperature strength and plasticity of medium- and high-carbon steels	5

The Influence of Surface-Active Elements on Grains Boundary Structure and Resistance Against Intergranular Corrosion of Austenitic Cr–Ni and Cr–Ni–Mo Steels	5
Influence of Eutectic-Type Inclusions on the Red Brittleness of Steels	5
Determination of fracture toughness of zirconia-based ceramics produced by the spark plasma sintering method	5
Change of the Modulus of Elasticity of the Surface Nonasrtuctured Layer on U8 Steel	5
Obtaining of biosoluble magnesium-based materials by powder metallurgy methods (a review)	5
Corrosion resistance, wear resistance, and tribocorrosion of Ni—Mo—B electrodeposited coatings	5
Determination of crack growth resistance characteristics of 15Kh2NMFA-A steel minispecimens	5
Comparison of the Corrosion Resistances of Welded and Brazed Joints Made of Galvanized 08Yu Steel	5
The influence of boride inclusions on the structure and properties of 04Kh14T3R1F steel intended for covers of spent fuel cassettes of nuclear power plants	5
Technology of Formation of Mesostructures in Sintered WC–Co and WC–Ni Solid Alloys	5
The influence of hydrogen-free glow discharge nitriding of 40Kh steel on the properties of the surface layer in long holes	5
The Influence of Inclusions on Mechanical Characteristics of Structural-Heterogeneous Materials (A review)	5
Formation Conditions and Properties of High-Entropy Alloys Creating σ-Phase	5
Wear Resistance of Glow-Discharge Nitride 08Kh18N10 Steel	5
The influence of stress ratio on properties and mechanism of nitinol fracture	5
Specific Features of Whisker Crystals Plastic Deformation	4
Optimization of the functional properties of anodically synthesized titanium dioxide with platinum-palladium-TiO2 composites	4
Quantum-Chemical Calculations of the Stability of Zeolite–Phosphate Complexes as Pigments of Paint Coatings	4
Methods of Investigation of the Deposited Metal Properties and Their Application for the Development of Flux Cored Wires	4
X-ray phase and structural studies of Ce–Zn–Ga alloys	4
Morphology and Porosity of the Surface of Titanium Alloys After Plasma-Electrolytic Oxidation in An Alkaline Environment with Diatomite	4
Stress-strain state of thin heterogeneous plates resting on a Winkler elastic foundation	4
Interaction of component and crystal structure of compounds in (Gd, Er)–Re–Ge and related systems at 1070 K	4
Corrosion Resistance of Additively Manufactured Titanium Alloys in Hydrochloric Acid	4
Synthesis and Investigation of ZrO2–SiO2 Oxide Alloyed with Sn(IV) Ions	4
Influence of Heating Modes on Heat-Resistance of Zr and Zr–1% Nb Alloy	4
Tensometric study of the stress-strain state of the fuel tank	4
Influence of the shape and location of orthotropic inclusion on the stress state of anisotropic body under longitudinal shear	4
Corrosion Resistance of Pseudoalloy Copper-Iron Coatings Obtained by Electric Arc Spraying	4
A Finite Element Comparison Between Two Sizes of NiTi Commercial Staples Used in Scaphoid Fracture Fixation	4
The influence of the crack morphology caused by delaminations in the operated ferrite-pearlite steel on its fracture toughness	4
Methodology of Calculation and Experimental Verification of Rigidity of Reinforced Concrete Structures with Unidirectional Cavities	4
Control of the formation of metal structure surface with flux-cored wires	4
Assessment of V96zs alloy properties under conditions simulating a thermal cycle of fusion welding	4
Effect of Temperature on Resistance to Pitting Corrosion in Duplex Stainless Steel 2205 Welds	4
Influence of Electrospark Coatings of Tool on Force Indices of Milling of Wooden Materials	4
Structure and Mechanical Properties of White Cast Iron After Plasma Surface Modification	4
The Influence of the Deformation and Heat Treatment on the Structure and Heat-Resistance of Ti–Al–Zr–Si Alloys	4
Corrosion-fatigue resistance of sucker rods with metallopolymer coatings	4