OOIR: Observatory of International Research

Papers

(The H4-Index of Advanced Engineering Materials is 36. The table below lists those papers that are above that threshold based on CrossRef citation counts [max. 250 papers]. The publications cover those that have been published in the past four years, i.e., from 2021-06-01 to 2025-06-01.)

Article	Citations
Masthead	130
Editorial for Special Issue of Field‐assisted Materials Processing: Recent Innovations and Microstructural Evolution	124
Deformation Behavior of 2D Composite Cellular Lattices of Ceramic Building Blocks and Epoxy Resin	92
Bioactive Fe Foam for Degradable Bone Graft Cages	85
Effects of Carbon Nanotube Infiltration on a Shape Memory Polymer‐Based Device for Brain Aneurysm Therapeutics: Design and Characterization of a Joule‐Heating Triggering Mechanism	84
3D Investigation of Damage During Strain‐Controlled Thermomechanical Fatigue of Cast Al–Si Alloys	75
Experimental and Numerical Studies of Densification and Grain Growth of 8YSZ during Flash Sintering	70
Physics‐Informed Multistage Machine Learning Strategy for the Nanomachining‐Induced Plastic Deformation Behavior	68
Microstructural Evolution and Mechanical Properties of Sn‐58Bi Solder Alloys with Different Cooling	66
Effect of Strain Rate on Microstructure and Mechanical Properties of Electroplastic Rolled ZrTi Alloy	65
Uniting a III‐Nitride Transmitter, Waveguide, Modulator, and Receiver on a Single Chip	65
N‐Doped and P‐Doped Graphene on MgO (111): A First‐Principles Study	59
The Effect of Anion Modification on the Conductive Polymer/Ag‐Interdigitated Electrodes Micro‐Supercapacitor	50
Surface Effect on Phase Transformation of Single Crystal NiTi Shape Memory Alloys Studied by Molecular Dynamics Simulation	49
Design and Development of In‐Process‐Resolution‐Tunable Stereolithography System Utilizing Two‐Photon Polymerization	49
Solution‐Based Approach for the Continuous Fabrication of Thin Lithium‐Ion Battery Electrodes by Wet Mechanochemical Synthesis and Electrophoretic Deposition	49
Masthead	46
Metal–Matrix Composites from High‐Pressure Torsion with Functionalized Material Behavior	46
Engineering the Atomic Interface of Refractory‐Metal‐Reinforced Copper Matrix Using Direct Ink 3D Printing	45
High‐Throughput Production of Gelatin‐Based Touch‐Spun Nanofiber for Biomedical Applications	45
Dielectric and Energy Storage Properties of Layer‐Structured Ba_n−3Bi₄Ti_nO_3n+3 (n = 4–7) Ferroelectrics	43
Breaking the Cardiovascular Flow Barrier for Dielectric Elastomer Actuator‐Based Pumping: Design and Characterization	43
Homogenization Heat Treatment and Tribological Properties of In Situ Alloyed NiTiCu by Laser Powder‐Bed Fusion	43
Impact of Sample Preparation Approach on Transmission Electron Microscopy Investigation of Sputtered AlNi Multilayers Used for Reactive Soldering	42
A Time‐Saving Method for Evaluating the Fatigue Strength of Carburized High‐Alloy Steel Containing Carbides	42

From Damage to Functionality: Remanufacturing of Thrust Roller Bearings by Tailored Forming	42
About the Impact of Defect Phases on the Thermoelectric Properties of Cr₃S_4–xSe_x	40
Durable Metallic Surfaces Capable of Passive and Active De‐Icing	39
Multi‐Hierarchical Microstructures Boosted Linearity of Flexible Capacitive Pressure Sensor	38
Analysis of the Meso‐Mechanical Deformation Behavior of Al Foams and Ni/Al Hybrid Foams Using Time‐Lapse Micro‐Computed Tomography Measurements and 3D Optical Flow	38
Intentional Oxidation and Laser Remelting of Highly Reflective Pure Cu for Its High‐Quality Additive Manufacturing	38
Resistive Switching of Perovskite‐Type Oxides Using the Hebb–Wagner Polarization Method	37
Tailored Nickel Base Multilayer Systems with Adjusted Grain Size and Chemical Composition	37
Mechanical Properties of Aluminum Matrix Syntactic Foams Manufactured with Aluminum Smelter Waste	37
Crumpled and Eccentric Nanospheres of Ti₃C₂T_x MXene by Aerosol Jet Printing on Heat Substrate	37
Approaching 1 GPa Ultra‐High Tensile Strength in a Nanostructured Al–Zn–Mg–Cu–Zr–Sc Alloy Prepared by Severe Plastic Deformation	37
Microstructure, Mechanical Properties, Corrosion Behavior, and in Vitro Assessment of Mg‐Zn‐Cu Alloy for Gastrointestinal Anastomosis Staple Application	36