OOIR: Observatory of International Research

Papers

(The median citation count of Journal of Mining and Metallurgy Section B-Metallurgy is 1. The table below lists those papers that are above that threshold based on CrossRef citation counts [max. 250 papers]. The publications cover those that have been published in the past four years, i.e., from 2022-08-01 to 2026-08-01.)

Article	Citations
Effect of equal channel angular pressing process on drawability of DC04 steel sheets	17
Enhancing microstructure, grain refinement, and wear properties of cast A356-TiB2 composite through improved sequence of ECAP and heat treatment processes	15
Effect of olivine as MgO-bearing flux on low- and high-alumina iron ore pellets	15
Effect of ECAP process on deformability, microstructure and conductivity of CuCoNi alloy	11
Study on the drying characteristics of green pellets of ultrafine iron ore concentrate	10
Oxidation and property evolution of AISI T5 steel under varying heat treatments	8
Characterizations and boron diffusion modelling on the AISI H13 steel	8
Thermodynamic measurements and ab initio calculations of the indium-lithium system	7
Two-stage leaching of germanium from copper cake under subsequent non-oxidizing and oxidizing conditions	7
Selection of pulverized coal fuel components for blast furnaces based on the study of physico-chemical processes during their heating	6
Effect of low aluminum additions in the microstructure and mechanical properties of hot forged high-manganese steels	6
Pyrometallurgical treatment of jarosite residue with a mixture of CaO, SiO2, and CaSi	6
Synergistic effect of Pd+Rh on the microstructure and oxidation resistance of aluminide coatings	6
Sb recovery from an As pre-removed lead anode slime using a ZnS-Na2CO3 smelting reduction	6
The melting performance blast furnace slags with high alumina content	5
Experimental investigation on WAAM-based functional hard-facing bimetallic part	5
A green approach to recovering lithium and cobalt from spent lithium-ion batteries using dilute HCl solution mixed with H. sabdariffa flower extract as a leaching agent	5
Comparative investigation of ultrasonic cavitation erosion for two engineering materials	5
Effects of welding parameters on percentage dilution and mechanical properties in welded joints of ultra-high hardness armour steels	4
Existent state and removal rate of silver in lead-silver slag during the melt-vaporization process	4
The influence of cold, warm and hot deformation on microstructure and mechanical properties of inconel 718 superalloy	4
Gold recovery and migration mechanism in the copper smelting and converting	4
Study on the fabrication of active CaO from steel slag of the converter and its application in CO2 adsorption process	4
Wear properties of Ni addition to Nb-V micro alloyed PM steels in dry and corrosive environment	3
Optimizing calcium additions for a strength-corrosion resistance balance in squeeze-cast Zn-Al-Cu-Mg alloys	3

Weldability study of dual phase and transformation induced plasticity automotive steels	3
Prediction model of blast furnace molten iron temperature and molten iron silicon content based on improved arithmetic optimization twin support vector machine for regression	3
Effects of hot rolling on microstructures, wear and corrosion resistance of Mo-Ni-W p/m alloyed steels	3
Effect of extrusion process on the stress corrosion cracking resistance of 7N01 aluminum alloy	3
Effect of rotation rates on dissolution behavior of lime in CaO-FeTo-SiO2-MgO system	3
Effect of water vapor on the reduction kinetics of hematite powder by hydrogen-water vapor in different stages	3
Thermal upgrading of manganese ores prior to smelting	3
Antimony recovery by hydrometallurgy - emphasis on recovery from leach solutions	3
Studying the structure and properties of quasi high-entropy alloys of the Fe-Co-Cr-Ni-Mn-Nb system with Mo additives	3
From the alloy design to the microstructural and mechanical properties of medium manganese steels of the third generation of advanced high strength steels	3
Evolution of microstructure under different homogenization conditions and its effect on recrystallization processes during hot rolling of AA5182 alloy	3
Microstructural, mechanical and thermodynamic properties ınvestigation of the novel rare earth-free multicomponent Mg-15Al-8Ca-3Zn-2Ba alloy	3
Separation of Co(II), Mn(II) and Ni(II) from the sulfuric acid leaching solution of lithium-ion battery by solvent extraction	2
Enhancing corrosion resistance and structural properties of $ \ce{Ni-TiO2} $ composite coatings: The impact of SDS surfactant	2
Effect of forging sequence and heat treatment on microstructure of high-duty power-plant shaft made of Cr-Mo ultra-high strength steel	2
Recovery of pure MnSO4 by crystallization after separation of Fe(III) and Zn(II) from the reductive leaching solution of manganese dust containing Mn3O4	2
Recent advances of the thermodynamic behavior of tin species in aqueous solution	2
Straight synthesis of α and γ alumina from kaolin by HCl acid leaching	2
Solidification behavior and environmental risk assessment of toxic elements on tailings from carbothermic reduction-magnetic separation of lead blast furnace slag	2
Thermodynamic description of the Mg-O and Al-O systems	2
Contribution to the study of toughness in creep resistant steel welded joint	2
Effect of adsorption of surfactant mixtures on wettability of sintering dust	2
Effect of copper addition on the microstructure, mechanical, thermal, and magnetic properties of Fe-Ni-Cu alloys	2
The role of Si at a lower level on the mechanical properties of Al-based automotive alloys	2
Investigating the Al-Cr-La ternary system: Al-rich corner phase equilibria at 600°C	2
Combing role of MgO and Al2O3 on viscosity and its correlation to structure of fluorine-free mold fluxes	2
The magnesium-palladium-silver system: Thermodynamic properties of the liquid phase	1
Corrosion of a chimney liner operated for 130,000 hours	1
Microstructure and hardness of bi-modified magnesium AZ31 alloys subjected to severe plastic deformation	1
Microstructure development, mechanical properties and underlying mechanism of micro-TiN-reinforced AlSi10Mg composites fabricated by selective laser melting	1
Influence of microstructure and crystallographic texture on hydrogen diffusion in IF-steel	1
Microstructure and abrasive wear resistance in the miller test of a martensitic Fe-C alloy with V and W carbides	1
Evolution behavior of oxide inclusions in Si-Mn deoxidized steel during billet heating process	1
The influence of nickel grade and its occurrence state on high pressure acid leaching behavior of lateritic nickel ores	1
Dissolution kinetic mechanisms of FeCr₂O₄ spinel in MgO-Al₂O₃-SiO₂ slag system: Elemental dissolution and component diffusion	1
Optimization of smelting process of magnesium based on machine learning	1
Lithium slag leach solution refining by hydroxide precipitation	1
A qualitative study of multiphase steel microstructure developed in four different steel alloys	1
Study of drying kinetics and moisture diffusivity in iron ore briquettes after using different drying techniques	1
Extraction and recovery of zinc, potassium, and sodium from blast furnace dust by ultrasonic-assisted ammonia leaching	1
Milling parameter optimization for the refinement of NiO/Al mixtures and the synthesis of Ni/Al2O3 nanocomposites	1
The impact of hot roll temperature on the microstructure and corrosion resistance of super duplex stainless steel, which is used to coat mild steel in seawater environments	1
Kinetics, nanomechanical and tribological characterizations of Fe2B layers on ASTM A29 steel	1
Hydrometallurgical processing of molybdenum middlings from Shatyrkul-Zhaysan cluster ore	1
Prediction of end-point phosphorus content of molten steel in BOF with machine learning models	1
Corrosion properties of aluminized 16Mo3 steel	1