OOIR: Observatory of International Research

Papers

(The TQCC of Journal of Mining and Metallurgy Section B-Metallurgy is 3. The table below lists those papers that are above that threshold based on CrossRef citation counts [max. 250 papers]. The publications cover those that have been published in the past four years, i.e., from 2021-11-01 to 2025-11-01.)

Article	Citations
Interdiffusion coefficient and atomic mobility for fcc Ag-Cu-Mg phase at 1073 K	10
Study on the drying characteristics of green pellets of ultrafine iron ore concentrate	9
Effect of equal channel angular pressing process on drawability of DC04 steel sheets	9
Microstructure and mechanical properties of A7N01 aluminum alloy weld joints filled with ER5356 and ER5087 weld wires	9
Thermodynamic modelling of the binary indium-lithium system, a promising li-ion battery material	9
Desulfurization of molten steel with molten slag using the electrochemical method	9
Effect of olivine as MgO-bearing flux on low- and high-alumina iron ore pellets	9
Enhancing microstructure, grain refinement, and wear properties of cast A356-TiB2 composite through improved sequence of ECAP and heat treatment processes	9
Two-stage leaching of germanium from copper cake under subsequent non-oxidizing and oxidizing conditions	7
Effect of partially reduced highly fluxed DRI pellets on impurities removal during steelmaking using a laboratory scale EAF	7
Effect of ECAP process on deformability, microstructure and conductivity of CuCoNi alloy	6
Thermodynamic measurements and ab initio calculations of the indium-lithium system	6
Selection of pulverized coal fuel components for blast furnaces based on the study of physico-chemical processes during their heating	6
Characterizations and boron diffusion modelling on the AISI H13 steel	6
Improvement of modeling on the Pidgeon process for magnesium production by introducing the variable thermophysical properties	6
Sb recovery from an As pre-removed lead anode slime using a ZnS-Na2CO3 smelting reduction	5
Effect of low aluminum additions in the microstructure and mechanical properties of hot forged high-manganese steels	5
The melting performance blast furnace slags with high alumina content	5
Pyrometallurgical treatment of jarosite residue with a mixture of CaO, SiO2, and CaSi	5
A green approach to recovering lithium and cobalt from spent lithium-ion batteries using dilute HCl solution mixed with H. sabdariffa flower extract as a leaching agent	5
Synergistic effect of Pd+Rh on the microstructure and oxidation resistance of aluminide coatings	5
Comparative investigation of ultrasonic cavitation erosion for two engineering materials	5
Experimental investigation on WAAM-based functional hard-facing bimetallic part	5
Existent state and removal rate of silver in lead-silver slag during the melt-vaporization process	4
Effect of strain energy on corrosion behavior of ultrafine grained copper prepared by severe plastic deformation	4

Gold recovery and migration mechanism in the copper smelting and converting	4
Weldability study of dual phase and transformation induced plasticity automotive steels	4
Study on the fabrication of active CaO from steel slag of the converter and its application in CO2 adsorption process	4
From the alloy design to the microstructural and mechanical properties of medium manganese steels of the third generation of advanced high strength steels	4
A new process for extracting vanadium by direct calcification using the heat of molten vanadium slag	4
Effect of water vapor on the reduction kinetics of hematite powder by hydrogen-water vapor in different stages	3
Prediction model of blast furnace molten iron temperature and molten iron silicon content based on improved arithmetic optimization twin support vector machine for regression	3
Thermal upgrading of manganese ores prior to smelting	3
Effect of extrusion process on the stress corrosion cracking resistance of 7N01 aluminum alloy	3
Microstructural, mechanical and thermodynamic properties ınvestigation of the novel rare earth-free multicomponent Mg-15Al-8Ca-3Zn-2Ba alloy	3
A novel method for alumina preparation by electrotransformation AlCl3 solution under NH4Cl-catalyzed and CO2-injected conditions	3
Effect of rotation rates on dissolution behavior of lime in CaO-FeTo-SiO2-MgO system	3
Use of ferric salt solutions as leaching agents of Co, Ni, Cu, Fe, and Mn from metallic alloys of spent lithium-ion batteries and separation of iron from the leaching solution	3
Effect of forging sequence and heat treatment on microstructure of high-duty power-plant shaft made of Cr-Mo ultra-high strength steel	3
Effect of coiling temperature on the structure and properties of thermo-mechanically rolled S700MC steel	3
Microstructure evolution and mechanical properties of TiB/Ti6Al4V composites based on selective laser melting	3
Effects of hot rolling on microstructures, wear and corrosion resistance of Mo-Ni-W p/m alloyed steels	3
Separation of Co(II), Mn(II) and Ni(II) from the sulfuric acid leaching solution of lithium-ion battery by solvent extraction	3