OOIR: Observatory of International Research

Papers

(The TQCC of International Journal of Mechanics and Materials in Design is 6. The table below lists those papers that are above that threshold based on CrossRef citation counts [max. 250 papers]. The publications cover those that have been published in the past four years, i.e., from 2020-05-01 to 2024-05-01.)

Article	Citations
The effect of negative Poisson’s ratio on the low-velocity impact response of an auxetic nanocomposite laminate beam	47
Tunable ultralow frequency wave attenuations in one-dimensional quasi-zero-stiffness metamaterial	45
Potential of combating transmission of COVID-19 using novel self-cleaning superhydrophobic surfaces: part I—protection strategies against fomites	40
Hygrothermal forced vibration of a viscoelastic laminated plate with magnetostrictive actuators resting on viscoelastic foundations	28
Application of artificial intelligence to optimize the process parameters effects on tensile properties of Ti-6Al-4V fabricated by laser powder-bed fusion	26
Thermo-rotational buckling and post-buckling analyses of rotating functionally graded microbeams	24
An analytical investigation of elastic–plastic behaviors of 3D warp and woof auxetic structures	23
On vibration of sigmoid/symmetric functionally graded nonlocal strain gradient nanobeams under moving load	23
Wave propagation in non-homogeneous asymmetric circular plate	21
Numerical and experimental analysis of the structural performance of AM components built by fused filament fabrication	18
Thermally induced nonlinear stability and imperfection sensitivity of temperature- and size-dependent FG porous micro-tubes	17
Thermal buckling of porous symmetric and non-symmetric sandwich plate with homogenous core and S-FGM face sheets resting on Pasternak foundation	16
Numerical and theoretical analysis of the dynamic mechanical behaviour of a modified rhombic dodecahedron lattice structure	15
Proficiency of statistical moment-based methods for analysis of positional accuracy reliability of industrial robots	15
Synergistic effect of surface-flexoelectricity on electromechanical response of BN-based nanobeam	14
Kinematic and dynamic analysis of a 3-DOF parallel mechanism	14
Optimal electromechanical bandgaps in piezo-embedded mechanical metamaterials	14
Simulating flexible origami structures by finite element method	13
Thermoelastic attenuation of circular-cross-sectional micro/nanoring including single-phase-lag time	13
Design optimization of hybrid uncertain structures with fuzzy-boundary interval variables	12
Response analysis of MEMS based high-g acceleration threshold switch under mechanical shock	12
Design and control of helicopter main reducer vibration isolation platform with magnetorheological dampers	12
Thermo-mechanical interactions in a functionally graded elastic material with voids and gravity field	12
Partially debonded circular inclusion in one-dimensional quasicrystal material with piezoelectric effect	12
Nanoindentation of a half-space due to a rigid cylindrical roller based on Steigmann–Ogden surface mechanical model	11

Transient response analysis of sandwich cylindrical panel with FGM core subjected to thermal shock	11
Design of multi-channel bypass magnetorheological damper with three working modes	11
Material stiffness optimization for contact stress distribution in frictional elastic contact problems with multiple load cases	10
Micromechanics-based modeling of elastic modulus and coefficient of thermal expansion for CNT-metal nanocomposites: effects of waviness, clustering and aluminum carbide layer	10
A design method of Voronoi porous structures with graded relative elasticity distribution for functionally gradient porous materials	10
Mesoscale analysis of rubber particle effect on young’s modulus and creep behaviour of crumb rubber concrete	9
Analysis on the removal mechanism of disc grinding based on dynamic thermal–mechanical coupling	9
A critical assessment and contact algorithm for the staggered grid material point method	9
Multimodal ellipsoid model for non-probabilistic structural uncertainty quantification and propagation	9
A topology optimization method for hyperelastic porous structures subject to large deformation	9
Advances in the development of superhydrophobic and icephobic surfaces	9
Multi-objective optimization of the active constrained layer damping for smart damping treatment in magneto-electro-elastic plate structures	9
Investigation of wrinkling behaviour in the creased thin-film laminates	9
Size-dependent nonlocal strain gradient modeling of hexagonal beryllium crystal nanoplates	9
Elastic buckling of nanoplates based on general third-order shear deformable plate theory including both size effects and surface effects	8
On the mechanical behavior of two directional symmetrical functionally graded beams under moving load	8
Isogeometric level set topology optimization for elastoplastic plane stress problems	8
Development and validation of an automated FEM-based design optimization tool for continuum compliant structures	8
Mechanism of resistance relaxation and hysteresis in viscoelastic piezoresistive polymer nanocomposites	8
Rotational energy harvesting from a novel arc-cylinder type vibro-impact dielectric elastomer generator	8
Potential of combating transmission of COVID-19 using novel self-cleaning superhydrophobic surfaces: part II—thermal, chemical, and mechanical durability	7
Dynamic stiffness formulation for transverse and in-plane vibration of rectangular plates with arbitrary boundary conditions based on a generalized superposition method	7
Optimal design of vibrating composite plate considering discrete–continuous parameterization model and resonant peak constraint	7
Reliability based topology optimization of thermoelastic structures using bi-directional evolutionary structural optimization method	7
Three-dimensional buckling analysis of variable angle tow composite laminated plates	7
Analytical-geometrical percolation network model for piezoresistivity of hybrid CNT–CB polymer nanocomposites using Monte Carlo simulations	7
Design of spatially varying electrical poling for enhanced piezoelectricity in Pb(Mg1/3Nb2/3)O3–0.35PbTiO3	7
Ultra-wideband outward-hierarchical metamaterials with graded design	7
Numerical model of large spatial deflections of bundled conductors in electrical substations	6
Numerical investigation on a bistable vibro-impact dielectric elastomer generator mounted on a vibrating structure with ultra-low natural frequency	6
Noncontact spatiotemporal strain mapping of composite multiferroic cylinders	6
Equivalent orthotropic properties of periodic honeycomb structure: strain-energy approach and homogenization	6
Nonlinear dynamic and bifurcations analysis of an axially moving circular cylindrical nanocomposite shell	6
A transient topology optimization with time-varying deformation restriction via augmented Lagrange method	6
Prediction of shear behavior of glass FRP bars-reinforced ultra-highperformance concrete I-shaped beams using machine learning	6