OOIR: Observatory of International Research

Papers

(The H4-Index of International Journal of Minerals Metallurgy and Materials is 49. The table below lists those papers that are above that threshold based on CrossRef citation counts [max. 250 papers]. The publications cover those that have been published in the past four years, i.e., from 2022-01-01 to 2026-01-01.)

Article	Citations
Fabrication and performance of 3D co-continuous magnesium composites reinforced with Ti2AlNx MAX phase	255
Mechanical properties of Al-15Mg2Si composites prepared under different solidification cooling rates	184
In situ carbon coating for enhanced chemical stability of copper nanowires	125
Factor analysis and machine learning for predicting endpoint carbon content in converter steelmaking	122
Highly dispersed NiMo@rGO nanocomposite catalysts fabricated by a two-step hydrothermal method for hydrogen evolution	110
Erratum to: Solid-state impedance spectroscopy studies of dielectric properties and relaxation processes in Na2O-V2O5-Nb2O5-P2O5 glass system	102
Instrumented oscillographic study on impact toughness of an axle steel DZ2 with different tempering temperatures	102
Growth kinetics of titanium carbide coating by molten salt synthesis process on graphite sheet surface	96
An environmentally friendly synthesis route: Low-temperature preparation of vacancy-ordered double perovskites Cs2SnX6 (X = Cl, Br, I) via ionic liquid	94
Effects of Li addition on the microstructure and tensile properties of the extruded Mg-1Zn-xLi alloy	92
Interface behavior of chalcopyrite during flotation from cyanide tailings	91
A thermodynamic perspective on electrode poisoning in solid oxide fuel cells	89
Hydration reactivity difference between dicalcium silicate and tricalcium silicate revealed from structural and Bader charge analysis	85
Numerical simulation on the multiphase flow and reoxidation of the molten steel in a two-strand tundish during ladle change	84
Combining the 8-hydroxyquinoline intercalated layered double hydroxide film and sol—gel coating for active corrosion protection of the magnesium alloy	78
Instantaneous transition of composition and morphology of inclusions with an initial Al2O3 composition in the molten steel during calcium treatment	76
Research progress in interface modification and thermal conduction behavior of diamond/metal composites	76
Stability enhancement of MnOx–CeO2 via hydrophobic modification for NO reduction by NH3	74
Recent progress on transition metal-based amorphous ribbons as electrocatalysts for water splitting	74
Fe-loaded S, N co-doped carbon catalyst for oxygen reduction reaction with enhanced electrocatalytic activity and durability	73
Enhanced prediction of occurrence forms of heavy metals in tailings: A systematic comparison of machine learning methods and model integration	70
Hydrometallurgical detoxification and recycling of electric arc furnace dust	70
Comprehensive status evaluation and prediction of blast furnace based on cascade system and combined model	66
Preparation of CIP@TiO2 composite with broadband electromagnetic wave absorption properties	66
Preparation of silver nanoparticles through the reduction of straw-extracted lignin and its antibacterial hydrogel	64

Design principles in MOF-derived electromagnetic wave absorption materials: Review and perspective	63
Multi-interface structure design of bamboo-based carbon/Co/CoO composite electromagnetic wave absorber based on biomimetic honeycomb-shaped superstructure	62
Alkyl chain modulation of asymmetric hexacyclic fused acceptor synergistically with wide bandgap third component for high efficiency ternary organic solar cells	60
Recycling and recovery of spent copper—indium—gallium—diselenide (CIGS) solar cells: A review	60
Effect of deformation parameters on the austenite dynamic recrystallization behavior of a eutectoid pearlite rail steel	58
Influence of unloading orifice size on the production of microsized ore particles by gas rapid unloading	56
Erratum to: Strengthening strategy for high-performance friction stir lap welded joints based on 5083 Al alloy	56
Modified Al negative electrode for stable high-capacity Al—Te batteries	54
Dynamic mechanical responses and debonding failure mechanisms of a bolt–resin–rock anchoring system subjected to cyclic shear loading	54
Mechanical behavior and response mechanism of porous metal structures manufactured by laser powder bed fusion under compressive loading	54
Edge effect during microwave plasma chemical vapor deposition diamond-film: Multiphysics simulation and experimental verification	54
Fabrication of green one-part geopolymer from silica-rich vanadium tailing via thermal activation and modification	53
Construction of enhanced multi-polarization and high performance electromagnetic wave absorption by self-growing ZnFe2O4 on Cu9S5	53
Microstructure and toughness of thick-gauge pipeline steel joint via double-sided friction stir welding combined with preheating	53
Two new amino acid derivatives as green corrosion inhibitors against Q235 steel in HCl solution: Experimental and theoretical investigations	52
KOH-assisted aqueous synthesis of bimetallic metal-organic frameworks and their derived selenide composites for efficient lithium storage	52
Heterogeneous information phase space reconstruction and stability prediction of filling body-surrounding rock combination	51
Electrolyte and current collector designs for stable lithium metal anodes	51
CO2 nanobubble-enhanced cement–fly ash backfill: Optimizing aggregate gradation and microstructure	51
Reaction behavior and non-isothermal kinetics of suspension magnetization roasting of limonite and siderite	51
Advancements in titanium nanocomposites: Microstructure and fretting wear resistance via spark plasma sintering	50
Effect of fluoride roasting on copper species transformation on chrysocolla surfaces and its role in enhanced sulfidation flotation	50
Microscopic damage evolution of anisotropic rocks under indirect tensile conditions: Insights from acoustic emission and digital image correlation techniques	50
New role of α phase in the fracture behavior and fracture toughness of a β-type bio-titanium alloy	50
Improving creep strength of the fine-grained heat-affected zone of novel 9Cr martensitic heat-resistant steel via modified thermo-mechanical treatment	49