Advances in Applied Ceramics

Papers
(The median citation count of Advances in Applied Ceramics is 1. The table below lists those papers that are above that threshold based on CrossRef citation counts [max. 250 papers]. The publications cover those that have been published in the past four years, i.e., from 2021-04-01 to 2025-04-01.)
ArticleCitations
Rapid microwave-assisted synthesis of rare-earth hexaborides powders61
3D printing of fibre-reinforced ceramic composites with hierarchical structure15
Preparation of zirconium diboride by reduction of zirconia with calcium hexaboride10
Mechanical and thermal insulation properties of carbon fibre-reinforced carbon aerogel composites9
From stoichiometric to non-stoichiometric high-entropy carbide: A case study of hafnium addition9
Localised surface modification of high-strength aluminium–alumina metal matrix composite coatings using cold spraying and friction stir processing9
Impact of Er substitution on the properties of NdFeO3: structural, magnetic and microwave absorption7
The effects of sintering additives on the ceramic matrix composite of ZrO2: microstructure, densification, and mechanical properties – a review7
Improving mechanical properties of carbon and tool steels via chromizing6
Catalytic performance of porous Yb2O3 sesquioxide6
Stability of 3Y-TZP nano zirconia powder after hydrothermal ageing treatment6
3D-printed porous Al2O3 membrane coated with hydrophilic modified titanium dioxide particles for large-flux oil/water separation5
Fabrication and characterisation of ZrO2-reinforced porous mullite ceramics5
Preparation of high-temperature active zirconium boride powders via precursor route and microwave sintering5
Low-temperature synthesis of Ti3SiC2 powders in mixed molten salts4
Preparation and tribological performance of CrAlTiCN coatings on 316L and TC4 substrates in sea water4
Influence of sintering temperature and Li+/Mg2+ doping on the thermoelectric properties of Bi2−2xLixMgxSr2Co4
Preparation and oxidation behaviour of MoSi2-SiC-Si-ZrB2 composite coatings on carbon surface via laser cladding4
Fabrication and characterisation of ZrSi2 ceramics via reactive hot-pressing4
Pressure slip cast processing of alumina (Al2O3) products and comparative evaluation of mechanical properties4
Novel intermediate temperature solid oxide fuel cell based on La-doped Bi4V2O11 electrolyte4
Strengthen the bonding of self-glazed zirconia to enamel by sol–gel coating4
A comprehensive review of modern engineered ceramics coatings for optimised resistance to wear and corrosion4
Effect of screw access hole on the fracture load of implant-supported monolithic zirconia single crown4
Fitness of self-glazed zirconia onlays using conventional and digital impressions3
Enhanced densification and ionic conductivity of LLZO by flash sintering3
Biphasic BiFeO3 ceramics based on rhombohedral and tetragonal polymorphs3
Time dependent deformation of LaCoO3 based perovskites at different temperatures: ferroelastic and non-ferroelastic creep behaviour3
Preparation of porous mullite ceramics consisting of needle-like mullite whiskers3
Clinical application of fully digital self-glazed ultra-thin zirconia veneers3
Plant extract-based biosynthesis of silver nanoparticle and silver–zinc nanocomposites-doped hydroxyapatite and its antimicrobial activity3
Ablation resistance of double-layer SiC /ZrB 2 -SiC-La 2 O 3 coating for SiC-coated graphite ex2
Effects of sol contents and sintering temperatures on SiO2 coated needled carbon fibre felt composites2
Effect of Sr2+doping on the microwave dielectric properties of BaZrO3ceramics2
Microstructure and resistivity of ITO targets sintered by cold and microwave sintering for solar cell applications2
Structure and properties study of magnesium oxide porous ceramics prepared by Organic Foam Template Method2
Structural, morphological properties and phase stabilisation criteria of the calcia-zirconia system2
Thermal stability of TiC–Ti3AlC2 and TiC–Ti3AlC composites during selective laser treatment2
Influences on the mechanical and physical properties of hot-press moulding alkali-activated slag (HP-FRAASC) composite with various fibers2
Influence of particle size and aggregates on translucent alumina ceramics fabricated by gelcasting2
The effect of Ti to the crystal structure of Li7-3xMxLa3Zr1.8Ti0.2O12 (M= Ga, In) garnet-type solid electrolytes as a second dopant2
Perovskite layered materials with A2B2O7 structures for high-temperature sensor applications – A comparative study2
Mechanical response and thermal expansion characteristics of spark plasma sintered Zr–La–B–C(O)-based precursor-derived ceramics2
Abrupt high grain growth in hydroxyapatite during flash sintering2
In vitro tribocorrosion evaluation of carbide-derived carbon (CDC) for hip implants2
Flash sintering mechanism in multiphase materials system of copper smelting slags2
Preparation and properties of graphene/β-SiC-toughened ceramics2
Enhancing the hardness of alumina-zirconia-CNT composites using alumina-graphite powder bath to provide homogeneous sintering2
Effects of Fe2O3 on crystallisation and properties of R2O–CaO–MgO–Al2O3–SiO2–Fe2O3 glass ceramics1
Enhanced ionic conductivity of NASICON-type NaTi2(PO4)3 solid electrolytes with sodium-ion conduction: based on NaF-assisted synthesis1
Development of environmental barrier coatings for non-oxide ceramics1
Facile and composition controllable synthesis of lanthanum-doped strontium titanate via peroxide route1
Microstructure characteristics and mechanical properties of Al2O3/MgAl2O4 directionally solidified eutectic ceramic1
Preparation of porous ceramsite from municipal sludge and its structure characteristics1
Wear behaviour of alumina-toughened-zirconia composites with different phase arrangement under ball-on-flat tribological tests1
Gel-casting for manufacturing porous alumina ceramics with complex shapes for transpiration cooling1
Preparation of porous titania particles by partial dissolution and hot-water or hydrothermal treatment of hydrous titania1
Sintering, microstructure, and mechanical properties of ZrO2-doped Al2O31
Influence of the sintering method on densification, microstructure and electrical conductivity of 12Ce-TZP1
Wear behaviour of graphene platelets reinforced WC-Co cemented carbide1
Preparation of aluminosilicate fiber-SiBOC composite foams for thermal protection applications1
Highly wear resistant dual-phase (Ti-Zr-Nb-Hf-Ta)C/(Ti-Zr-Nb-Hf-Ta) B2 high-entropy ceramics1
Rapid evaluation of the particle-erosion resistance of Al2O3 ceramics, composites, and coatings using a resonant acoustic mixer1
Binder jetting printing of zirconia structures via grading powder and epoxy binder1
Enamel (glassy) coatings for steel protection against high temperature corrosion1
A review on the manufacturing techniques of porous hydrophobic ceramic membranes applied to direct contact membrane distillation1
Ca-ATZ/Ca-ATZ+SiO2 functionally graded ceramic1
Highly flexible and strong SiC fibre mats prepared by electrospinning and hot-drawing1
Early hydration and mechanical strength of calcite–ettringite seeds added cement mixture for 3D printing1
Electron redistribution and acid site of tungsten-doped CeTiOx with oxygen vacancies1
Evaluation of the trueness and precision of ceramic laminate veneers fabricated with four computer-aided manufacturing methods1
Surfactant assisted dip-coating method for deposition of polyethylmethacrylate-diamond coatings1
1.2697429656982