IET Electric Power Applications

Article	Citations
Investigation into fault tolerant capability of new modular low‐speed and high‐torque direct‐drive permanent magnet motor based on unequal span winding	38
Effect of end leakage inductance on the performance of toroidal winding double‐sided linear induction motors	22
Cover Image	21
Modelling of high frequency bearing voltage for dual‐winding permanent magnet synchronous generators	21
Thermal behaviour analysis of a high voltage inverted‐type current transformer	21
A review of finite control set model predictive control for linear machines	19
Pseudorandom high‐frequency injection synchronous reluctance motor sensorless control with parameter variation consideration	18
Multi‐level optimisation design of a yoke‐less axial‐field flux‐switching permanent magnet motor considering the fault‐tolerant capability	16
In‐depth investigation of inter‐turn short‐circuit faults of surface‐mounted permanent magnet machines with series‐parallel coil connections	15
A novel measurement‐protection‐integrated current transformer based on hybrid core and magnetic field sensor	14
Demagnetisation fault analysis and diagnosis based on different methods in permanent magnet machines ‐ An overview	14
Design and transient experimental analysis of a pulsed brushless doubly fed alternator in a capacitor charge power supply system	14
Investigation of winding cooling enhancement and thermal modelling of large‐power high‐torque‐density direct‐drive PMSM	14
Design and modelling of a two‐degrees‐of‐freedom dual‐rotor axial‐flux squirrel cage induction motor	13
PM Eddy Current Loss Calculation Based on Magductance for FSPM Machine	13
Calculation of magnetic field and eddy current loss in end clamping ring of 300MVA synchronous condenser based on a novel semi‐analytical method	13
Fault diagnosis of oil‐immersed transformers based on the improved sparrow search algorithm optimised support vector machine	12
Rare‐earth‐free Al‐Ni‐Co hybrid PMa‐SyRM for an air‐conditioner compressor	12
Electromagnetic and experimental analyses of a low‐cost miniature tubular moving magnet linear oscillating actuator for miniature compressor applications	11
A novel online method for locating fault coil in direct‐drive permanent magnet synchronous motor with inter‐turn short‐circuit fault using search coil array	10
Design and modelling of three‐to‐five phase three‐limbed transformer	10
Supply and demand balance control of electrical submersible linear motor for offshore oil exploitation	10
Evaluation of ability to withstand short circuit and development of large capacity 500 kV autotransformer	10
	10
Real‐time estimation of the synchronous generator dynamic parameters using actual phasor measurement unit data and experimental evaluations	10

A high‐efficiency magnetic‐geared double‐rotor machine with the coreless stator for hybrid aircraft propulsion	10
	10
Modal analysis of the stator system of a permanent magnet synchronous motor with integer slot multi‐pole pair for electric vehicles	9
Back propagation neural network‐based torque ripple reduction strategy for high frequency square‐wave voltage injection‐based interior permanent magnet synchronous motor sensorless control	9
Design of high power density double‐stator permanent magnet synchronous motor	9
The occurrence and mechanism of hysteresis between axial deformation and short‐circuit electromagnetic force during the vibration of power transformer windings	9
Analysis of a novel flux adjustable axial flux permanent magnet eddy current coupler	9
A peak time shifting phenomenon in transformer axial short‐circuit electromagnetic force due to the coupling of electromagnetic‐axial vibration	9
Self‐compensation of torque reaction in an induction contra‐rotating propulsion motor	9
An induction machine‐based drive system and supervisory control for application to smart water‐pumped storage and networks	8
Adhesion control strategy for trains with driven independently rotating wheels considering active guidance	8
Improved active power dynamic response of voltage‐controlled doubly fed induction generator	8
High‐frequency harmonic suppression method for interleaved traction converters based on synchronous sampling	8
Design and analysis of a new feature optimisation method for circuit breakers defect identification	8
Dual‐port network‐based impedance modelling and AC‐port characteristic analysis of wound rotor synchronous machine for more electric aircraft	8
Analytical prediction of the open‐circuit magnetic field for the V‐shaped interior PM machine by the improved subdomain method	8
End‐winding wire‐insulation heat conduction model for precise thermal predictions of permanent magnet synchronous machines	8
Cross‐coupling control strategy based on intelligent adaptive control for cross‐shaped dual‐axis linear motors	8
Mathematical sizing and design analysis of permanent magnet vernier machine for contra‐rotating wind power applications	8
Active disturbance rejection current controller with time delay compensation predictive ESO for aircraft PMSM drive	7
Research on non‐linear active disturbance rejection speed synchronisation control of aviation dual motor actuator considering current saturation constraints	7
A novel axial air‐gap transverse flux switching PM generator: Design, simulation and prototyping	7
2‐D analytical magnetic model for optimal design of an outer rotor permanent magnet synchronous machine	7
Design of multi‐phase permanent magnet synchronous motor with fractional‐slot windings for electromagnetic vibration reduction considering stator teeth modulation	7
Model‐based online efficiency control of induction motor drives based on nonlinear technique	7
Research on Torque Ripple Suppression of Open‐Winding BLDCM Based on Zero Vector	7
Optimal starting frequency of three‐phase induction motor	7
Modelling and suppression of bearing voltage of wind turbine permanent magnet synchronous generators	7
A new air gap flux‐based technique to detect loss of field in synchronous generators	7
	7
Multi‐objective hierarchical optimisation design and experimental verification of an alterable‐magnetic‐circuit variable‐flux memory machine	7
A new four‐row integral transposition method of stator windings and circulating current loss reduction in large turbo generators	7
Analysis of electromagnetic vibration of IPM motor based on vector control for electric propulsion ships	6
Incorporating the coupled effects of slot opening, armature reaction and saturation in the model of the airgap flux density distribution of permanent magnet synchronous machines	6
	6
Litz wire loss performance and optimization for cryogenic windings	6
An integrated approach of a field‐circuit coupling model and multi‐physics finite‐element simulation for analysing transient electromagnetic vibration of pump motors	6
Discrete‐time full‐order sensorless control of high‐speed interior permanent magnet synchronous motor in electric vehicle traction system	6
Backstepping control of three‐degree‐of‐freedom hybrid magnetic bearing based on non‐linear disturbance observer	6
Robust flux angle control of induction motors to improve efficiency at light loads	6
Modelling and Predictive Control of Electromechanical Actuators for All‐Electric Nose Landing Gear Systems	6
Design and analysis of concave‐core stator direct‐drive permanent magnet motor	6
Transfer learning‐based surrogate‐assisted design optimisation of a five‐phase magnet‐shaping PMSM	6
	6
Analysis of magnetic pole loss and heat in a tubular hydro‐generator based on 3D electromagnetic field–thermal network modelling	6
Improved loss minimisation control for interior permanent magnet synchronous motor based on loss angle optimisation	6
Multi‐parameter identification method of induction motor based on coupling and small signal injection	6
	6
A method for calculating the time‐varying equivalent circuit parameters of large‐capacity synchronous condenser considering field mutual leakage reactance	6
Incipient detection of stator inter‐turn short‐circuit faults in a Doubly‐Fed Induction Generator using deep learning	6

A Fast Calculation Method of 3D Temperature Field of Oil‐Immersed Transformer Based on Point Cloud U‐Net++ Neural Network	6
The fourth order flux observer with in‐loop filter for permanent magnet synchronous motor sensorless control	6
Corrigendum: Dynamic air gap asymmetry fault detection in single‐sided linear induction motors	6
A new approach for top‐oil thermal modelling of power transformers using Unscented Kalman filter considering IEEE C57.91 standard	5
	5
Time‐harmonic field‐circuit model for brushless doubly fed induction machine	5
Dual‐inertia flywheel energy storage system for electric vehicles	5
Quantitative assessment on synchronisation capability of a line‐start permanent magnet synchronous motor with hybrid rotor	5
3D flux configuration cost effective switched reluctance motor with small torque ripple content; design and prototyping	5
	5
Finite‐element calculation of electromagnetic characteristics and steady‐state stability of dual‐excited synchronous generator	5
Performance analysis and design optimization of asymmetric interior permanent magnet synchronous machine for electric vehicles applications	5
Design and finite element analysis of a high‐performance surface‐permanent magnet synchronous reluctance machine with optimised robustness towards demagnetisation	5
Research on cogging torque reduction method for permanent magnet synchronous motor accounting for the magnetic pole edge effect	5
Investigation of the impact of rotor shaping on the torque and radial force harmonics of a V‐shape interior permanent magnet synchronous machine	5
Derating factor determination of the three‐phase induction motor under unbalanced voltage using pumping system	5
Flux‐adjusting characteristic analysis and optimization design of variable‐leakage‐flux interior permanent magnet motor	5
Active cogging torque construction by the weld slot design in a positioning servo system	5
Analysis and detection of turn‐to‐turn short circuit fault in a permanent magnet Vernier generator based on modified winding function	5
Analysis of different stator winding topologies for fractional horse power brushless direct current motors	5
Standardisation concept for rapid testing of effects of cutting on losses of electric steel and amorphous ribbon	5
Virtual position predictive control with system delay observer to improve PMLSM position tracking accuracy	5
Transformer partial discharge fault diagnosis based on improved adaptive local iterative filtering‐bidirectional long short‐term memory	5
An improved double‐vector model predictive control strategy for four‐switch three‐phase inverter‐fed permanent magnet synchronous motor based on visualisation analysis considering DC voltage pulsation	5
	5
Sub‐Synchronous Oscillation Suppression Strategy for DFIG Based on Morris‐EFAST Global Sensitivity Analysis and Multi‐Parameter Co‐Optimisation	5
Influence of rotor excitation source model in electromagnetic field–circuit coupling analysis model of tubular hydro‐generator on no‐load voltage waveform and damper winding loss calculation results	5
An ampere‐second‐vector pulse width modulation technique and fault‐tolerant control for CSI11 fed five‐phase permanent magnet synchronous motor with multiple harmonic electromotive forces	5
A super‐high‐speed PM motor drive for centrifugal air compressor used in fuel cell unmanned aerial vehicle	5
High‐dimensional optimal design of dual‐rotor synchronous reluctance machines based on data‐driven torque decomposition	4
Power Transformer Fault Diagnosis Method Based on SMOTE and Convolution Soft Threshold Network	4
Analytical calculation of magnetic field of double‐stator permanent magnet spherical motor considering cogging effect and edge effect	4
Active noise control by means of high frequency injection in electric motors	4
Reduced‐order electromagnetic transient model based on equivalent flux linkage derivative for induction motors under voltage sag condition	4
Effect of rotor magnetic isolation dimensions on no‐load performance of ultra‐low speed high torque spoke type permanent magnet motor	4
Impact of stator slot geometry on the windage loss in a high‐speed linear switched reluctance motor	4
Various Control Strategies Performance Assessment of the DFIG wind turbine connected to a DC grid	4
Design, analysis and prototyping of a PM‐assisted synchronous reluctance machine equipped with new‐type of fractional‐slot winding	4
Optimising the flux barriers of interior permanent magnet machine for noise reduction under certain load conditions	4
Generating characteristics and experimentation of counter rotating dual rotor wound field flux switching wind generator	4
	4
A novel cogging torque measurement method for multi slot/pole permanent magnet motor	4
High‐frequency square‐wave voltage injection position sensorless control method using single current sensor	4
Research on dual‐winding permanent magnet generator system with integrated dual‐channel controller	4
New analytical algorithm for calculating the end leakage magnetic field of a 300Mvar synchronous condenser under no‐load condition	4
Design and experimental analysis of high electromagnetic force density moving magnet linear actuator with end ferromagnetic poles	4
An equivalent and simplified approach for acoustic noise prediction in a PM synchronous motor based on the semi‐analytical‐FEM model	4
Guest Editorial: Advances in electric machines — solutions for electro‐mobility with improved characteristics	4
A modified partitioned‐stator flux‐switching permanent magnet machine for enhancing torque‐density in electric vehicle powertrains	4
Modelling of brushless doubly fed reluctance machines based on reluctance network model	4
Improved equation to describe the induction motor currents during nearby three‐phase short‐circuits	4
Impact of close proximity pulse width modulation switching events on electric machine terminal voltages	3
A maximum efficiency point tracking control method for ultrasonic motors with temperature compensation	3
Short‐circuit current difference of parallel strands in winding turns and its influence on the distribution of electromagnetic force	3
Analysis of Mechanical Characteristics and Operation Risk of Synchronous Condenser Rotor Under Dynamic Conditions With Typical Fault	3
A fast calculation method of transient hot spot temperature for the design of dry‐type on‐board transformers	3
Dynamic multi‐agent dc‐bus reconfiguration in modular motor drives with a stacked polyphase bridge converter	3
Neural network based robust optimal energy control of pulse width modulation‐inverter fed motor driving pump	3
Design and analysis of a novel asymmetric PM‐assisted synchronous reluctance motor used for electric vehicles	3
Magnetic field and rotor impedance analysis of solid rotor induction motors using the multilayer analytical method	3
Research on rotor unbalance magnetic pull compensation method based on modular winding d‐axis current injection	3
Modified magnetic equivalent circuit model for magnetic field analysis of one cage‐rotor induction motor used in electric submersible pumps	3
Analysis of rotor winding interturn short circuits affected by the initial dynamic eccentricity in large synchronous condensers	3
Analysis and Suppression of Nonswitching High‐Frequency Band Vibration in Fractional‐Slot Concentrated‐Winding Permanent Magnet Synchronous Machines	3
Non‐linear model of the switched reluctance motor with included core losses’ effects	3
Co‐simulations of induction machines coupled with a radial ball bearing for mechanical defects analysis	3
	3
Model predictive current control with lower switching frequency for permanent magnet synchronous motor drives	3
Novel Winding Design and Analysis of Brushless Wound Rotor Synchronous Machines	3
Reduction of losses in dual‐permanent‐magnet‐excited Vernier machine by segmented stator for electric aircraft	3
Analysis of capacitive discharges in motor bearings under different operation conditions	3
Fast calculation method of transformer harmonic magnetic field based on radial basis function augmented surrogate model	3
Hybrid flux predictor‐based predictive flux control of permanent magnet synchronous motor drives	3
Method for acquisition of orthotropic material parameters and calculation of modal frequencies in permanent magnet synchronous motor	3
Further investigation of convolutional neural networks applied in computational electromagnetism under physics‐informed consideration	3
	3
Improving the performance of helical motion resolver based on accurate modelling of longitudinal end effect	3
Modelling and analysis of electromagnetic force, vibration, and noise in permanent magnet synchronous motor for electric vehicles under different working conditions considering current harmonics	3
Analysis of a spoke‐type ferrite PM motor with assisted poles based on equivalent magnetic network with hybrid cross‐shaped mesh elements	3
Improvement of operation and maintenance efficiency of power transformers based on knowledge graphs	3

Implementation of a DSP‐based speed‐sensorless adaptive control for permanent‐magnet synchronous motor drives with uncertain parameters using linear matrix inequality approach	3
Analytical modelling for magnetic field of interior permanent magnet synchronous motors accounting for bridge saturation	3
Enhanced robust diagnosis of multiple‐type demagnetisation fault for permanent magnet synchronous motor based on D‐axis magnetic network model using magnetic field reconstruction	3
Modified magnetic equivalent circuit of double‐stator single‐rotor axial flux permanent magnet machine considering stator radial‐end flux‐leakage	3
Thermal analysis and temperature evaluation on a magnetic‐geared dual‐rotor machine	3
Research on Digital Analysis Method of Transformer Hot Spot Temperature Based on BP Neural Network Optimised by Genetic Algorithm	3
A new three‐level simplified sparce NPC topology for UHS PMSM motor applications	3
Static sensor assisted rotor temperature estimation of permanent magnet machine for the low‐speed servo applications	3
Analytical modelling and analysis of magnet eddy current loss in magnet‐surrounded permanent magnet synchronous machine caused by stator slot effect	3
An analytical fast field solver for surface permanent magnet co‐axial magnetic gears	3
Influence of slot/pole number combinations and pole shaping on electromagnetic performance of permanent magnet machines with unbalanced north and south poles	3
Few‐sample multi‐objective optimisation of a double‐sided tubular machine with hybrid segmented permanent magnet	3
Maximum torque per ampere control of permanent magnet/reluctance hybrid rotor dual stator synchronous motor	2
Predictive AI Maintenance of Distribution Oil‐Immersed Transformer via Multimodal Data Fusion: A New Dynamic Multiscale Attention CNN‐LSTM Anomaly Detection Model for Industrial Energy Management	2
A novel method for transformer fault diagnosis based on refined deep residual shrinkage network	2
Reduction of inappropriate principal features of the switched reluctance motor using sinusoidal rotor configuration	2
Design and analysis of a novel yokeless mover permanent magnet linear generator for free piston engine converter	2
Parameter identification of transformer lumped element network model through genetic algorithm‐based gray‐box modelling technique	2
Optimal Trajectory‐Based Thermal Balance Control Strategy of Wide Input Voltage Dual Resonant Cavity LLC Converter for Vehicle Power Supply	2
Model predictive control for energy efficient AC motor drives: An overview	2
Semi‐flooded cooling for high torque density modular permanent magnet machines	2
Analytical modelling of the linear transverse flux permanent magnet motor using magnetic equivalent circuit method	2
A full‐domain fluidic‐thermal approach for a high‐speed PMSM considering the bearing components	2
Hybrid low switching frequency modulation strategy with high dynamic response for high‐power voltage source converter	2
Electrical machines surrogate‐based design optimization based on novel waveform targeting strategy with improvement of the computational efficiency	2
Fault‐tolerant operation for five‐phase permanent magnet synchronous machine drives with five‐phase six‐leg inverter	2
	2
Fault diagnosis of inter‐turn short circuits in PMSM based on deep regulated neural network	2
Temperature estimation of water cooling stator windings considering twisted structure and resistance distribution	2
Comparison and analysis of different rotor structures of double‐stator permanent magnet synchronous motor	2
	2
Fault Diagnosis and System Reconfiguration Based on Switching Sequence Technology for ANPC Three‐Level Cascaded Inverter	2
Advances in control of power electronic converter connected drive and generation systems	2
A phase‐shift‐free synchronous reference frame filter‐based position sensorless control method for open‐winding permanent magnet generator system	2
Calculation, simulation and fast estimation of thermal resistance of rotary voice coil actuators	2
Detent force suppression of permanent magnet linear synchronous motor based on a V‐shaped tooth‐slot structure	2
Improved coordinated control for thyristor controlled series compensation and generator excitation	2
Study on abnormal power failure shutdown control of magnetic suspension centrifugal compressor	2
Design of a non‐ferromagnetic spoke array Vernier permanent magnet generator with iron‐bar based on enhanced equivalent magnetic network model	2
Terminal characteristics measurements and analysis of the three‐phase Active Front‐End converter building block	2
Copper loss analysis and loss separation method in a dynamic process of ultra‐high speed motor with slotless stator	2
A systematic review on current research and developments on coreless axial‐flux permanent‐magnet machines	2
A novel artificial neural network approach for residual life estimation of paper insulation in oil‐immersed power transformers	2
2‐D Electromagnetic Analysis Coupled With 3‐D Thermal Analysis of a Dual‐PM Excited Flux‐Switching Generator With Overhang Structure for Direct Drive Wind Turbines	2
A direct field‐circuit coupled analytical modelling method for permanent magnet motor operation performance analysis	2
Fake algebraic Riccati equation applied to model predictive control for doubly fed induction generator direct power control	2
High efficiency single‐pulse controlled switched reluctance motor drive based on novel multilevel converter	2
The effect of end windings and the bearing labyrinth seals on stray capacitances and bearing voltage ratio of AC motors	2
	2
Research on efficient design method of high torque motor with dual airgap hybrid rotor for aircraft engines	2
Analysis of linear permanent magnet switched reluctance motors with modular and segmental movers	2
A Power availablE Estimation Tool for real‐time estimation in aircraft generators	2
Primary component segmental design to suppress the normal force ripple for the permanent magnet linear synchronous motor	2
	2
	2
Impedance modelling and stability assessment for grid‐connected dual‐PWM adjustable speed drives with motor torque oscillations	2
Optimization of stator ventilation structure of high‐speed railway traction motor based on the genetic algorithm	2
Harmonic voltage phasor reconstruction and harmonic state estimation based on the measurement data of a capacitive voltage transformer	2
Mechanical fault diagnosis of on‐load tap‐changer based on improved variational mode decomposition and relative density‐based outlier score	2
Time‐optimal finite control set model predictive control of non‐isolated DC–DC converters	2
A Modular Multi‐Port Hybrid Solid‐State Transformer for Large‐Scale Renewable Power Applications	2
A dual fuzzy logic controller‐based active thermal control strategy of SiC power inverter for electric vehicles	2
	2
Performance evaluating of rotor arrangement on high torque density in‐wheel permanent magnet machines	2
Modelling and analysis of the intersecting axis permanent magnet eddy‐current coupler	2
Research on core loss prediction of low‐frequency transformer based on Grey Wolf optimisation algorithm optimised Back Propagation neural network	2
Research on transformer fault diagnosis based on ISOMAP and IChOA‐LSSVM	2
Turn‐to‐turn and phase‐to‐phase short circuit fault detection of wind turbine permanent magnet generator based on equivalent magnetic network modelling by wavelet transform approach	2
Direct torque control and space vector modulation‐based direct torque control of brushless doubly‐fed reluctance machines	2
An analytical model of an eddy‐current coil near the edge of a conductive plate	2
Electromagnetic Forces and Vibrations Under Stator and Rotor Reference Frames in Permanent Magnet Synchronous Machines	2
	2
Research on current sharing control of parallel inverters used on electric motor emulator	2
Nonlinear‐disturbance‐observer‐based predictive control for trajectory tracking of planar motors	2
Hybrid analytical model for air‐gap magnetic field prediction of surface‐mounted permanent magnet motors with a quasi‐regular polygon rotor	2
Torque Characteristic Analyses and Multi‐Objective Optimisation of Multi‐Layer Flux‐Barrier Less‐Rare‐Earth Permanent Magnet Synchronous Machine	2
	2
Transient thermal models of induction machines under Inter‐turn short‐circuit fault conditions	2
Utilisation of regenerative braking energy in adjacent power sections of railway systems	2
Suitable claw shape design for improving the magnetic properties of forged claw pole parts in generator	1
Analytical model of a fractional slot double‐layer‐winding vernier permanent magnet machine	1
Fault diagnosis of high‐voltage circuit breaker based on open‐set theory fusion model	1
Analytical model of no‐load axial force for electric propulsion conical motor in electric aircraft	1
Robust virtual‐vector model predictive control of permanent‐magnet motor considering D‐Q axis inductance parameter uncertainty	1
Performance evaluation of a new modular split‐tooth permanent magnet‐assisted switched reluctance motor	1
Optimal sizing of a high‐speed flywheel in an electric vehicle using the optimal control theory approach	1
Design procedure and optimisation methodology of permanent magnet synchronous machines with direct slot cooling for aviation electrification	1
Analysis and inhibition of radial electromagnetic force in composite magnetic coupler	1
Analytical model of a dual‐stator spoke‐type permanent magnet synchronous machines accounting for tooth‐tips	1
Design and implementation of a parametric battery emulator based on a power converter	1
Current harmonic suppression strategy for permanent magnet synchronous motor based on small phase angle resonant controller	1
Super‐spiral sliding mode controller design for single‐winding bearingless switched reluctance motor	1
Study on two‐stage optimal scheduling of DC distribution networks considering flexible load response	1
A bridgeless configured asymmetrical alternating current–direct current converter‐based isolated single‐stage electric vehicle battery charger with supply side power factor enhancement	1
Model‐Free Adaptive Super‐Twisting Sliding Mode Speed Control Based on RBFNN Estimator for PMLSM Drive Systems	1