OOIR: Observatory of International Research

Papers

(The TQCC of Journal of Advanced Mechanical Design Systems and Manufacturing is 2. The table below lists those papers that are above that threshold based on CrossRef citation counts [max. 250 papers]. The publications cover those that have been published in the past four years, i.e., from 2022-05-01 to 2026-05-01.)

Article	Citations
Preface for the Special Issue on Design, Concurrent Engineering and Smart Manufacturing in the Era of VUCA	16
Cutting process in non-step drilling of deep hole with tool wear progress	12
A physical knowledge-guided and data-driven framework for remaining useful life prediction (The case of turbofan engines)	10
Calculation and experimental analysis of rough cutting of cycloidal bevel gear by forming method	9
Thermal modeling techniques designed for high-speed directed energy deposition coatings	8
Mobile parallel manipulator consisting of two nonholonomic carts and their path planning	7
A portable multifunctional ophthalmic device for remote self-examination of the eye	6
Stress correction factor in load capacity estimation standard, JIS B 1759, for plastic gears	6
A novel modelling of glue allowance prediction for time-pressure dispensing system based on gated recurrent unit and fully connected neural network	6
Investigation of thin-wall geometry and hardness of mild steel additive manufacturing using resistance seam welding	6
Errata: A flexible topological flank modification method based on polynomial interpolation function [Journal of Advanced Mechanical Design, Systems, and Manufacturing, Vol. 17, No. 3 (2023), JAMDSM004	6
A cross-domain intelligent fault diagnosis method based on feature transfer with improved Inception ResNet for rolling bearings under varying working condition	6
Analysis of cutting parameters for enhanced dimensional accuracy in polytetrafluoroethylene groove cutting	5
Visualization of skin layer formation process on the aqueous colloidal solutions surface in the inkjet nozzle by using dynamic light scattering method	5
Preface	5
Non-parametric data-driven approach to reliability-based topology optimization of trusses under uncertainty of material constitutive law	5
Meshing performance investigations on oblique worm drive	5
Effects of temperature conditions on Gestalt factors for velvet hand illusion	5
Mechanism and test analysis of rail corrugation	5
Design method and parameter optimization of small angle rake face of hourglass worm gear hob	5
Development of tool life prediction system for square end-mills based on database of servo motor current value	5
Development of a motorless walking assistive device for foot flexions with instant torque output in gait cycle	4
Fault diagnosis of press dies using dynamic mode decomposition of a sound signal	4
A study on kansei attraction of products’ online reviews by using text mining and kano model	4
Automatic extraction of blood cells in bone marrow examination with an automatic imaging instrument	4

Minimizing waiting time under precedence constraints in health examinations	4
Design optimization of an adhesive-based modular fixture for postprocessing powder bed fusion workpieces	4
Experimental study on the interface topography evolution and vibration monitoring in thrust ball bearings induced by particulate contamination	4
Fast simulation of machining error induced by elastic deformation of tool system in end milling	4
Optimization design method of compliant cylindrical intershaft gas film seal using grasshopper optimization algorithm	4
Design and dynamic analysis of a slider-crank-based deformable wheel for stair-climbing vehicles	4
Tool-wear estimation for small-diameter ball-end mill with overlap machining	4
Detecting nicked automotive transmission gears in the final inspection by multi-scale time synchronous averaging	4
Efficient robust project schedule method based on iterated local search with high-speed simulations	3
Prototyping of vibration-sensing-actuation device to realization of future intelligent infrastructure	3
Turtle shell-inspired exosuit with large output, model-based torque estimation, and load compensation	3
Application of adaptive MCKD method optimized by SSA based on mixed strategy in rolling bearing fault diagnosis	3
Multi-objective optimized design for modified cycloid-pin gear drive mechanism based on load-bearing capacity	3
Investigation of the effect of multi-segment cutter section on meshing characteristics for face-hobbed hypoid gears	3
A study on tooth profile design and loaded tooth contact analysis for 2S-C type planetary gear drives	3
Tool state prediction model of Tent-ASO-BP neural network based on multi-feature fusion	3
Geometric generation method and experimental study of gear pair with point contact pattern	3
Topology optimization of analog circuit design via global optimization using factorization machines with digital annealer	3
A mathematical model for optimal switching problem of production line based on the OCRA method for ergonomics	3
Machining method and experiment for segmental spiral flute rake faces of hourglass worm gear hob	3
Investigation of kinesthetic illusion of biceps brachii muscle using a miniature voice coil motor	3
Influence of vibration conditions on tool life in low-frequency vibration cutting of difficult-to-cut materials	3
Defect detection of bearing side face based on sample data augmentation and convolutional neural network	3
A machine learning approach for simulation of multi-stage laser forming process	3
Novel quarter elliptical combinations chainring - the design and verification	3
Integrating continuous fuzzy Kano model and fuzzy quality function deployment to the sustainable design of hybrid electric vehicle	3
An upgradable product-service system design method based on kaos and time-axis	2
Process design and tool path generation for end milling considering tool life	2
Basic investigation of velvet hand illusion using a dot matrix for haptic display development	2
Experimental investigation of power transmission efficiency at various shaft angles using a pair of spherical gears	2
Chip breaking by triangular tool path in turning process	2
Lateral motion of slender endless flat belt in two-roller belt system with in-plane misalignment	2
Return error simulation analysis and experimental study for RV reducer with ADAMS	2
Preface	2
Iterative learning control-based ripple compensation in web handling systems	2
Construction and application of data-driven knowledge adjacency network for product CMF design	2
Automated NC program generation for hole drilling and swarf machining by 5-axis indexing machining	2
Modelling of cutting force in hard whirling of ball screws based on uncut chip geometry	2
Research on simplification of face gear tooth surface design	2
Research on the flow field and vibration characteristics of aerostatic bearing with conical chambers	2
Circumferential spatial tooth profile modification of flexspline for strain wave gear (A novel method and a case study)	2
Tool path generation in pocket machining considering workpiece deformation using Finite Element Method (FEM)	2
Principle of surface texture generation and tribological properties generated by ultrasonic vibration cutting	2
Evaluation of a robotic palpation sensor system for prostate cancer screening on silicone elastomers and prostate phantoms	2
Research on hobbing accuracy of flexspline tooth profile of harmonic drive	2
Research on obstacle avoidance for aerial work vehicle booms with light arrays based on an improved gradient projection method	2
Data–driven product form design integrating affective and functional requirements via TGRA–QFD and Stable Diffusion	2
Development of the spindle shaft for machining center using high thermal conductivity material	2
Adaptive grinding method and experimental verification of worm gear tooth surface knife marks	2
Effects of saccadic and scent stimulations on driver attentiveness in automated driving systems	2

One-degree-of-freedom planar link leg mechanisms design without predetermined trajectory using a genetic algorithm	2
Construction and finite element simulation of a square laser loading model that can replace circular spot superposition in laser peening forming	2
Directly mounted sol-gel composite piezoelectric devices by spray coating technique for high temperature ultrasonic transducers	2
Multi-objective optimization of visual and tactile desirability of wooden textures	2
Effect of arc length on deposition characteristics in rotary tungsten inert gas (TIG) torch	2
Advanced tooth profile roughing system (Innovating gear skiving with diamond-shaped edge tools)	2
Reducing load during partial forging of a disc specimen by applying lateral oscillation	2