OOIR: Observatory of International Research

Papers

(The TQCC of Asia-Pacific Journal of Chemical Engineering is 3. The table below lists those papers that are above that threshold based on CrossRef citation counts [max. 250 papers]. The publications cover those that have been published in the past four years, i.e., from 2021-04-01 to 2025-04-01.)

Article	Citations
Extension of lubricant drain interval by modified pure biomass oil filter	31
Design of Fractional‐Order Sliding Mode Controller for an Unstable Three‐State Model Jacketed CSTR	26
Impact of dope extrusion rate and multilayer polydimethylsiloxane coating on asymmetric polyethersulfone hollow fiber membrane for CO₂/N₂ and CO₂/CH₄ separa	25
Selective adsorption and separation of salicylic acid and 4‐hydroxyisophthalic acid from industry‐grade 4‐hydroxybenzoic acid on UiO‐66	24
Synthesis of ZrO₂‐NdO‐based mixed nanomaterial using green capping agent and its functionalization as electrode material for energy devices: Pseudo capacitors and water splitting	23
Correction of the cracking mechanism ratio in catalytic cracking process to characterize the thermal cracking reaction and realize highly sensitive identification of catalysts	20
	19
	19
Issue Information	17
Thermo‐Rheological Performance Evaluation of GNPs‐WO₃/Engine Oil Hybrid Nanofluids During Laminar Flow Inside a Horizontal Tube	15
A new Co‐based cathode with high performance for intermediate‐temperature solid oxide fuel cells	14
Preparation and photocatalytic mechanism of magnetic Ag₂S/CoFe_1.95Dy_0.05O₄ Z‐scheme heterojunction	13
An insight into the investigation of partition characteristics of flow fields based on chaos fractal theory in a jet impingement–negative‐pressure reactor	13
Research on application of twisted oval tubes in rod‐baffle heat exchangers	12
Ammonium nickel‐cobalt phosphate nanoflowers on highly conductive carbon fibers as an electrode material for enhanced electrochemical performance supercapacitors	12
Experimental study on seepage flow characteristics of leaked molten salt in foundation fillers in concentrating solar power plants	12
Measurements and predictions of phase equilibria in quinary system NaCl + KCl + MgCl₂ + SrCl₂ + H₂O (saturated with NaCl) at 308.2 K	12
Effects of air inlet and outlet on thermal management of electric vehicle battery pack equipped with fins	11
K₂CO₃ on porous supports for moisture‐swing CO₂ capture from ambient air	11
Kinetics of microwave carbothermal reduction of Sb₂O₃: Isothermal and non‐isothermal microwave thermogravimetric analysis	11
Promoted catalytic performance of sugarcane bagasse ash supported by γ‐alumina as efficient, stable, and ecofriendly catalyst for dehydration of methanol to dimethyl ether	11
Hydrodynamic analysis of nanofluids flow over 45° inclined porous square cylinder using Darcy–Brinkman–Forchheimer model	10
Effects of baffle on cycle‐to‐cycle variation in stirred vessel driven by paddle turbine using quadruple proper orthogonal decomposition	10
Enhancement in kerosene droplet–coal particle collision and adsorption by bubble trailing vortex in coal slurry conditioning: Energy evolution of collision process	10
Graphene oxide‐carboxymethyl cellulose hydrogel beads for uptake and release study of doxorubicin	9

Suspension of a single sphere in a stirred tank with transitional flow	9
Orthogonal Analysis for Structural Optimization of Ejector for Multiejector Air Curtain	9
Online evaluation of the boiler energy efficiency associated with the soot blowing in coal‐fired power plants	9
Experimental investigation of sedimentation behaviour using cerium oxalate particles in oxalic‐nitric acid medium	8
Effect of Ca–Fe composite catalysts on pyrolysis performance of demineralised anthracite and its char structure transformation	8
Efficient hydrolysis of cellulose to reducing sugars over peanut shell‐derived carbon‐based solid acid with a large surface area	8
Exploration of entropy analysis and viscous dissipation on radially convective flow of (Cu‐Al₂O₃:H₂O) hybrid nanofluid over a stretching disk	8
Carboxylated CNTs‐polyvinyl fluoride based electrical film heaters with improved mechanical properties	7
Highly efficient catalytic transfer hydrogenation of 5‐hydroxymethylfurfural to 2,5‐dimethylfuran over Cu_xZnAl catalysts	7
Novel feedforward‐feedback‐based continuous process transition strategy for chemical industry	7
High fire stability cement composite cementitious material based on semi‐dry gas desulfurized ash/blast furnace slag system: The synergistic effect of nano‐TiO₂ and nano‐SiO₂	7
A novel concept for pure hydrogen production and a massive reduction in CO₂ emissions from the formaldehyde absorption process	7
Decomposition kinetics of sodium amalgam in fixed bed of WC‐coated tubular SS‐304 packing: Modelling and validation	7
Issue Information	7
Effect of process impurities on crystallization thermodynamics and nucleation kinetics of taurine	7
Impact of reacting pressure on Na thermal transformation in two full‐scale devices using Zhundong coal at similar temperature	7
Efficiency enhancement of a combined cycle power plant by thermal integration of multiple waste heat streams with organic Rankine cycle	7
Experimental investigation of the strength characteristics of low‐temperature fouling containing ammonium bisulfate in boilers	6
Steady‐state and dynamic control of hydrocracking tail oil distillation process for high‐valued products	6
Study on solid‐air dendrite growth and motion with thermosolutal convection‐diffusion using non‐isothermal PF‐PSLBM model	6
Single step encapsulation process of ivermectin in biocompatible polymer using a supercritical antisolvent system process	6
Effect of supercooling phenomenon on liquid freezing in cylindrical vessel	6
Extraction of rosmarinic acid from Salvia officinalis L. using tunable deep eutectic solvent and its physiochemical properties	6
A method for the determination of shear viscosity of power–law fluids in a rectangular duct and concentric annulus	6
Effect of methanol on surfactants and surfactant–PEO mixtures	6
Influence of BaZnCuO₃ and BaZnCuO₃/rGO on the thermal decomposition of ammonium perchlorate and 3‐nitro‐3H‐1,2,4‐triazol‐5‐one (NTO)	6
Relationship between the deterioration of bleachability index (DOBI) value and hydrogenation performance for the hydrogenation of split‐crude palm oil (s‐CPO) in the oleochemical industry	6
Dividing‐wall column for separating wide boiling mixture: Optimal design and servo control strategy	6
Effects of nanometer magnesium hydroxide on soil cadmium form under different cadmium levels	6
Disjunctive fuzzy optimisation of electricity generation by biomass power producers in a feed‐in tariff programme	6
19th Asian Pacific Confederation of Chemical Engineering (APCChE) Congress 2022: Working towards a sustainable society—Special issue	6
Process simulation and economic assessments for biodiesel production catalyzed by green Nanocatalysts	6
Modelling and simulation of thermal runaway phenomenon in lithium‐ion batteries	5
Area‐alterable liquid electrode capacitance sensor for water holdup measurement in oil–water two‐phase flow	5
Towards more efficient hydroformylation of long‐chain alkenes in aqueous biphasic system using microbubbles	5
Synthesis of alkynyl alcohol derivatives and its corrosion inhibition on N80 steel in 5 M HCl	5
Experimental study of metal‐oxide nanoparticles on the thermal properties of erythritol for thermal energy storage	5
Composite From Superparamagnetic Iron Oxide Nanoparticles and Copper Benzene‐1,3,5‐Tricarboxylate as Rapidly Regenerated CO₂ Adsorbent	5
Suppression of thermoacoustic instability and NOx emissions of unsteady swirl premixed flame with upstream microjets	5
The solid/porous compound wavy microchannel heat sinks with 45° secondary channel flow of thermo‐hydraulic performance	5
A Numerical Simulation Study on Condensation Heat Transfer Performance of Serrated Spiral‐Finned Tube	5
Modelling and control in drinking water treatment plants: A case study using time‐varying feedforward control	5
Effect of raw material composition on combustion behavior of quasi‐particles in the iron ore sintering process	5
Convective flow of ethylene glycol‐silver Jeffery nanofluid in a Hele‐Shaw cell with an influence of external magnetic field	5
Facile Preparation and Enhanced Visible Light Photocatalytic Performance of AgI/Ag₃PO₄/WO₃·H₂O Heterojunction Photocatalysts	5
Supercharging green chemistry: Unleashing 1, 4‐NADH regeneration and unprecedented C(sp³)‐F bond activation via NiS‐NiO/S‐g‐C₃N₄ nanocomposite photocatalyst under sola	5
Calotropis procera Latex Extract as an Effective Green Corrosion Inhibitor for Mild Steel in Acidic Medium: Experimental and Quantum Chemical Approaches	5
Study on porous layer formation kinetics under CO₂‐aqueous conditions via partial‐bounceback lattice Boltzmann method	5
Influence of the parallel oil‐secondary air and F‐layer secondary air distribution on the flow, combustion, and NOx generation characteristics of FW down‐fired boilers retrofitted with a stable	5
Electrochemical performance of yttria‐doped SrCoO_3‐δas cathode material for anode‐supported solid oxide fuel cell	5

Facile preparation of dual functions zeolite‐carbon composite for zinc ion removal from aqueous solutions	5
Enhanced photocatalytic degradation of tetracycline hydrochloride by Ag/AgI/WO₃·H₂O composites	5
Degradation of iron‐nickel alloy interconnects in contact with lanthanum nickelates based double‐layer electrodes during long‐term tests	4
Repurposing Plastic Waste Into Chemically Activated Carbon as Functional Adsorbents: Kinetic Analysis for Phenol Degradation and Methylene Blue Adsorption	4
Microencapsulation of pyriproxyfen using the particles from gas‐saturated solutions process as a controlled‐release system	4
Assessment of the adsorption capacity of phenol on magnetic activated carbon	4
Preparation of calcium aluminate and spinel by hydrolysis and calcination from secondary aluminum dross	4
Synthesis, characterization, and computational study of N‐protected amino acid inhibitors as well as assessment of corrosion resistance properties on mild steel in .5 M H₂SO₄ sol	4
Synthesis of oxygen‐rich functional groups biochar for high‐efficiency adsorption of herbicide and as a potential carrier for pH‐responsive slow release	4
Study on the combination of the annular jet pump and static mixer to improve the fluid‐carrying capacity of gas wells	4
K₂CO₃‐loaded γ‐Al₂O₃ for acid removal in waste transformer oil	4
Study on causes and laws of crystallization blockage for dolomite tunnel drainage pipeline	4
Microstructural and thermal properties of thermally cured calcined cow bone/kaolin filled hybrid polystyrene composites	4
Effect of transverse vortex on performance of wave plate demister	4
Correction to “Investigation of molecular interaction, performance of green solvent in esterification of ethanol and acetic acid at 298.15 K and at 1 atm”	4
Investigation of the Products and the Migration of Sodium and Chlorine During Pyrolysis of High‐Sodium Coal Mixed With Phosphorite	4
Dry methane reforming with nickel–cobalt bimetallic catalysts based on halloysite nanoclay modified by alkaline melting method	4
Removal of thiophene compounds from model fuel with supported copper on active carbon, adsorption kinetics, and isotherms	4
Effects of cathode gas diffusion layer type and membrane electrode assembly preparation on the performance of immobilized glucose oxidase‐based enzyme fuel cell	4
Performance study of self‐excited oscillatory cyclone drainage tool to improve the efficiency of natural gas well drainage and gas recovery	4
Experimental combustion characteristics and NO_x emissions for a 600‐MWe utility boiler after the retrofitted: Effects of load variation	4
Role of extracted nanosilica from rice husk on the structure, property and biodegradability of low density polyethylene/starch biodegradable film	4
The effect of inorganic salt on multiphase flow characteristics in a microbubble column: A focus on the ionic strength	4
Analysis of heat and mass transfer phenomena in peristaltic transportation of hyperbolic tangent fluid in tapered channel	4
Nitrogen‐doped biochar as an efficient sensing material for the electrochemical detection of heavy metal ion Pb²⁺ and Cd²⁺	4
Effect of steel slag bed material on ash deposition and Na migration in circulating fluidised bed during Zhundong lignite combustion	4
Numerical study of the falling film wettability and heat transfer on the inclined plates with different corrugated structures	4
Controllability robustness of heat exchanger network based on complex network theory	4
Indirect solution modeling of melting behavior of SiO₂ based on the image processing technology	4
Optimal Linearization–Based Computationally Proficient Predictive Control of MIMO Nonlinear System Using Least Square Support Vector Machine	4
Numerical study on active droplet generation governed by pulsatile continuous‐phase flow	3
Experimental research on fully burning high‐alkali coal in a 300 MW boiler with slag‐tap furnace	3
Separation and thermal conversion of group components from medium‐low‐temperature coal tar pitch	3
Development of a novel artificial neural network model for closed pulsating heat pipe with water and aqueous solutions	3
Leakage Characteristics of Hydrogen Gas Carrying Alkaline Solution	3
Study on the performance of a vortex mist eliminator for improving the separation efficiency of fine particles	3
Effect of 915‐MHz low‐temperature microwave irradiation on the molecular structure of coking coal	3
Characterization of Particle Fluidization in a New Type of Fluidized Bed Flotation Unit	3
Efficient removal of emerging pollutant oxytetracycline by cost‐effective biochar–hydroxyapatite composite	3
Catalytic and noncatalytic CO₂ abs‐desorption studies of MEA‐TETA‐DEEA/MEA‐TETA‐AMP tri‐solvents at specific blended ratios	3
Revealing flow structures in horizontal pipe and biomass combustor using computational fluid dynamics simulation	3
Apparent and true mineralization during combined electro‐oxidation and electro‐coagulation on stainless steel anode	3
Liquid water transport mechanism inside fuel cells with orderly graded perforation microporous layer	3
A short review on recent advances in porous adsorbents for separation of oxygen from atmospheric air	3
Preparation of hollow carbon nanospheres from oxidation of spent tyre oil‐derived carbon black in air	3
Effect of O₂ concentration on combustion behavior and kinetics of coal gangue during oxy‐fuel combustion and oxy‐steam combustion	3
Synthesis of mesocarbon microbeads from high‐temperature coal tar pitch: Effects of quinoline insoluble	3
Influence of Fe‐modified Mn–Ce–Fe–Co–O_x/P84 catalytic filter materials for low‐temperature NO removal synergistic Hg⁰oxidation	3
Study on the adsorption of volatile gasoline components via HKUST‐1: Isobutylene as a model compound	3
Optimal detuning of multivariable proportional integral controller based on data‐driven approach for an activated sludge process	3
Ni@C@CNT catalyst derived from CNT doped Ni‐MOF for furfural hydrogenation to tetrahydrofurfuryl alcohol	3
High‐pressure high‐temperature fluid displacement by foam injection within a multiblock matrix‐fracture system	3
Corrosion and protection of galvanized steel in vegetation‐growing concrete in marine environment (I): Corrosion performance	3
Studies of polyurethane foams prepared with hybrid silicon and hydroxymethylated lignin	3
Experimental study on the mechanism of nanoparticles improving the stability of high expansion foam	3
Effect of chemical desulfurization on coal properties and sulfur structure based on microwave technology	3
Hydrophilic modification of feed spacer and its impacts on antifouling performance of reverse osmosis membrane	3
Issue Information	3
Treatment of wastewater containing high concentrations of ammonia nitrogen using ion exchange resins	3
Laminar flame speed measurement and combustion mechanism optimization for ethylene–air mixtures	3
DL‐malic acid for inhibiting the re‐ignition of long‐flame coal and its micro‐reaction mechanism	3
Effect of Ce doping on the catalytic performance of xNiCeO_y@SiO₂ catalysts for dry reforming of methane	3
Experimental investigation of Zhundong high‐calcium coal ash adhesion characteristics on metal surfaces at high temperatures	3
Multi‐Objective Optimization for Short‐Term Scheduling Considering Crude Oil Mixing Requirements Based on Improved NSGA‐III	3
Effect of seed on synthesis of binder‐free mordenite for dimethyl ether carbonylation	3
Ammonium removal by alkaline‐activated coconut coir from synthetic and ground waters	3
Acid sulfite pulping of Acacia mangium and Eucalyptus pellita as a pretreatment method for multiproduct biorefineries	3
Preparation and electrochemical properties of nitrogen‐doped carbon electrode material	3
Jute fibre reinforced unsaturated polyesters laminate preparation using eggshell filler	3
Nonnoble metal oxides for high‐performance Zn‐air batteries: Design strategies and future challenges	3
Experimental study of solid circulation rate and pressure distribution characteristics in a cold fluidized bed with an external heat exchanger in an municipal solid waste incinerator	3
Improved synthesis of cobalt‐doped TiO₂ catalyst using ultrasound and subsequent application for Acid Violet 7 degradation	3
Management of physical and chemical water quality in Kotchener drain (Kafr El Sheikh, Egypt)	3
Experimental study on sloshing mechanical characteristics in a partially filled storage tank	3
Research on the gas–solid corrosion characteristics of 316L alloy fiber filter bags in halogen hydride atmosphere	3
Hollow CoNiS polyhedrons/MnCoNi layered double hydroxide nanorod arrays on nickel foam as integral electrodes for improved oxygen evolution reaction in alkaline media	3
Sensitive and highly selective biosensor based on innovative V₂O₅ nanoparticles for detection of glutathione	3
Application of PC‐SAFT EoS and SCFT for the modeling of thermophysical properties comprising deep eutectic solvent and alcohols	3