Emerging Materials Research

Papers
(The TQCC of Emerging Materials Research is 2. The table below lists those papers that are above that threshold based on CrossRef citation counts [max. 250 papers]. The publications cover those that have been published in the past four years, i.e., from 2022-06-01 to 2026-06-01.)
ArticleCitations
Obituary: Allen W. Apblett18
δ phase precipitation in cast alloy IN625 with varied Cr content and associated properties17
Prevention of weld decay in TIG-welded AISI 304 steel pipes12
An experimental study on the sulfuric acid resistance of mineral additive mortars12
Assessing morphological effect on antimicrobial activity using needleless electrospinning11
Effect of cure parameters on void content and mechanical properties of composite laminates10
Editorial8
Citrus waste oil and turmeric for antibacterial, mosquito-repellent cotton fabrics8
Low-velocity impact behavior of abaca/epoxy composites with layer variations6
Preparation of metal–organic framework-199 (Cu) and their effects on catalytic decomposition of hexahydro-1,3,5-trinitro-s-triazine6
A comprehensive investigation on wear and corrosion performance of AISI 8620 steel after severe vibratory peening6
Strongly coupled relative humidity sensor coated with graphene oxide/polyvinyl alcohol composite5
Role of bond coat deposition method in the hot corrosion behavior of CSZ thermal barrier coatings5
First-principles modeling of molecular adsorption on an InSe monolayer5
Li+ transportation mechanisms in the halide solid-state electrolytes Li3YCl6 and Li3InCl65
Preparation, characterization, and structural studies of methylcellulose/CuO hybrid materials5
Editorial: Engineering materials with mechanical property improvement5
Effect of surfactant PEG on the property control of Bi2O3 and its photocatalytic activity4
Deep learning prediction of gamma-ray-attenuation behavior of KNN–LMN ceramics4
Effect of shot peening on fatigue performance of austenitic stainless steels4
A novel embroidered textile RFID adapted rectenna for current rectification and energy transfer4
Editorial: Fibrous materials for emerging applications4
The role of coarse aggregates in hydrophobized hydraulic concrete4
Editorial: Controlling interfaces at multiscale level in a material: toward properties enhancement4
Preparation of mesophase-pitch-based graphite foams at atmospheric pressure4
Cr-doped CdS and ZnS nano/microstructures with ferromagnetic properties4
Recycled PET particle effects on mechanical and dynamic properties of GFRP composites4
Constitutive model of additively manufactured FeCoCrNi high-entropy alloy3
Editorial: Enriching material properties towards performances improvement3
Numerical study on the failure mechanism of GFRP T-joint under low-velocity impact3
Experimental investigation of magneto-mechanical behavior of magnetorheological elastomers3
Foam concrete with untreated phosphogypsum and fly ash: strength and microstructure3
Edge effect on helium outgassing from ultralow expansion glass3
Design, characterization and applications of direct-current plasma source3
1D randomized photonic crystals: influence as single- and dual-channel narrowband filter3
Fabrication process optimization of nHA–CNTs-reinforced PEEK hybrid nanocomposite3
Iron-material-facilitated methane production from anaerobic wastewater treatment3
Reaction mechanisms of pristine and Cu-doped ZnO clusters with ethanol using Evans–Polanyi principle3
Study on the mechanical and tribological properties of C/C composites by CVI and PIP3
The effect of stirrup spacing and hook angle on RC cantilever beams with iron chip waste3
Numerical study on the GFRP T-joint failure under three-point bending2
Improved thermal stability of nanostructured surface on Al 6082 alloy by (Zr+Yb) addition2
Assessment of surface texturing of sustainable HVOF sprayed Al2O3+C powder coating2
Research on the influence of clay shock on inert slurry in shield-tunneling construction2
Nanocomposite (S3Sb2) x (S2Ge)100−x chalcogenide glasses: structural and physical properties2
Expansion potential of skin grafts with novel rotating-triangle-shaped auxetic incisions2
Antioxidant and enzyme inhibition activities of Spartium junceum with HPLC-DAD profiling2
Sensitivity enhancement of SPR biosensor employing heterostructure blue phosphorus/MoS2 and silicon layer2
Basic properties, durability and microstructure of alkali-activated hemihydrate phosphogypsum incorporating with ground granulated blast furnace slag (GGBFS)2
Chemically reduced silver nanoparticles: preparation and applications2
Influencing effects of variant laser pulse energy on fatigue behavior induced by LSP2
Emerging Materials Research : Reviewers 20252
Development and evaluation of coal mine waste materials for gainful utilization2
Gamma-ray-shielding parameters of carbon–aramid epoxy composites2
Tensile and microstructural behavior of gas-tungsten-arc-welded electrolytic tough pitch copper joints2
Increasing the adhesion forces of hydroxyapatite B, F, and Zr-reinforced coatings2
Preparation and electromagnetic wave absorption of compressible graphene aerogels2
Flake-shaped ZnFe2O4 nanoparticles: synthesis, characterisation and photocatalytic study2
Effect of forging pressure on microstructure and properties of friction welded steel tubes2
Editorial: Materials with multidisciplinary applications2
Single-layer woven carbon fibers improved the thermal and mechanical properties of epoxy resin2
Deterioration law and mechanism of autoclaved aerated concrete under sulfate attack2
Magneto-sensitive elastomers – materials, fabrication, and characterisation: state of the art2
Structural, electrical and thermistor behavior of BiFeO3–PbZrO3 for energy-storage devices2
A risk-based decision making framework to analyze the properties of cobalt–chromium alloys2
The structural and optical properties of PVA/CMC copolymer cured by UV irradiation for different times2
Improving asphalt concrete resistance to rapid freeze–thaw effect using HIPS polymer2
0.10471820831299