OOIR: Observatory of International Research

Papers

(The H4-Index of Metals is 52. The table below lists those papers that are above that threshold based on CrossRef citation counts [max. 250 papers]. The publications cover those that have been published in the past four years, i.e., from 2022-08-01 to 2026-08-01.)

Article	Citations
Oil-Retention and Oil-Bearing Tribological Properties of Nanoporous Copper Prepared Using a Chemical Dealloying Method	155
Effect of Si on Interfacial Reactions, Defect Evolution, and Mechanical Properties of Hot-Dip Galvanized Coatings	150
Crystallization of Fe-W-B Amorphous Powder Prepared by Gas Atomization	147
Effects of Graphite Particle Content and Holding Time on the Microstructure and Mechanical Properties of the Graphite/AZ91D Composite	137
The Influences of Micro-Alloying Element Sn and Magnetic Field on the Microstructure Evolution of Al–Bi Immiscible Alloys	128
The Effect of Interrupted Homogenization on β-Al5FeSi → α-Alx (Fe and Mn) Si Transformation in the A6063 Aluminum Alloy	118
Interfacial Cracking Failure Mechanism of Chromium-Coated Zircaloy Cladding for ATF Materials	108
Infrared-Guided Thermal Cycles in FEM Simulation of Laser Welding of Thin Aluminium Alloy Sheets	106
Resistance of Heterogeneous Metal Compositions to Fracture under Dynamic and Cyclic Loads	95
Additive Technologies, Advanced Joining Technology and Study of Weld Joints	92
The Effects of Post-Welding Heat Treatment on the Cryogenic Absorbed Energy of High Manganese Steel Weld Metal	82
Electrohydraulic Crimping of Tubes within Rings	82
Tensile and Bending Behaviour of Steel–Glass Fibre-Reinforced and Non-Reinforced Steel–Polyamide Sandwich Materials	78
Electromagnetic Preparation of Materials: From Fundamentals to Applications	77
Numerical Modeling of Materials under Extreme Conditions	76
Advances in Corrosion and Protection of Materials (Second Edition)	75
Friction Stress Analysis of Slag Film in Mold of Medium-Carbon Special Steel Square Billet	73
Process Studies on the W-C-Ti System Using a High-Throughput Laser-Based Additive Manufacturing Approach	72
Efficient Crystal Plasticity Modeling of Lath Martensite Considering Block Boundary Effects	71
Effect of La/Zn on Microstructural Evolution and Mechanical Properties of Extruded Mg-9Gd-3Y Alloy	71
Material and Process Modification to Improve Manufacturability of Low-Lead Copper Alloys by Low-Pressure Die Casting Method	70
Isothermal Oxidation Kinetics of Iron Powders Under Vapor Atmosphere	66
Data-Driven Performance-Oriented Rapid Process Optimization for 316 Stainless Steels Prepared by Laser Powder Bed Fusion	65
Self-Organization in Metal Plasticity: An ILG Update	65
Effects of Natural Aging and Discontinuous Cyclic Loading on High Cycle Fatigue Behavior of Steels	64

Optimization of Nitrogen Injection via Top-Blown O2–N2 Mixed Gas in BOF Steelmaking for Enhanced Rebar Performance	64
Mechanical Behaviors and Damage Mechanisms of Metallic Materials	64
Research and Application of the Original Position Statistical Distribution Analysis Method for Non-Metallic Inclusions in P91 Steel	63
Acknowledgment to the Reviewers of Metals in 2022	62
Superior Plasticity of Silver-Based Composites with Reinforcing Pyrochlore	62
The Effect of Process Parameters on the Pore Structure of Lotus-Type Porous Copper Fabricated via Continuous Casting	61
Thermodynamic and Technological Studies of the Electric Smelting of Satpaevsk Ilmenite Concentrates	61
Optical Recrystallization of Nanocrystalline Silicon Ribbons	61
Rheological Behavior of TRIP600 Steel during Deformation	60
Recent Advances in Metallurgical Extractive Processes	60
Assessing the Influence of Operational Variables on Process Performance in Metallurgical Plants by Use of Shapley Value Regression	59
The Effect of Thermal Treatment on Microstructure and Thermal-Induced Martensitic Transformations in Ni44Fe19Ga27Co10 Single Crystals	59
Dynamic Load Identification of Unspecified Metal Structures by Measuring Their Response	59
Effects of Aging Processes on the Dynamic Impact Mechanical Behavior of Mg-Gd System Alloys	58
Cause Analysis and Solution of Premature Fracture of Suspension Rod in Metro Gear Box	58
Simulation for Discrete Elements of the Powder Laying System in Laser Powder Bed Fusion	58
Study on the Strength Characteristics of Ion-Adsorbed Rare Earth Ore Under Chemical Leaching and the Duncan–Chang Model Parameters	58
Synergistic Effect of Pre-Aging and Nitriding on the Microstructure and Wear Resistance of L-PBF Manufactured 18Ni300	57
Role of Magnetism in Lattice Instability and Martensitic Transformation of Heusler Alloys	56
Influence of Structural Disorder on the Magnetic Order in FeRhCr Alloys	55
Study on Liquid Metal Embrittlement Susceptibility of T91 Exposed to Liquid Lead-Bismuth Eutectic	55
Detonation Spraying of Ni-Based Composite Coatings Reinforced by High-Entropy Intermetallic Particles	55
Wear of End Mills with Carbon Coatings When Aluminum Alloy A97075 High-Speed Processing	54
Failure Analysis of Two HP-Nb Heat-Resistant Tubes after 46,000 h Exposure to Reformer Service Conditions	54
Anomaly Detection in WAAM Deposition of Nickel Alloys—Single-Material and Cross-Material Analysis	53
Uncertainty Analysis of Plane Strain Fracture Toughness (KIC) Measurements of R350HT Rail Steels According to ASTM E399	52
Study on the Deformation and Fracture Mechanisms of Plastic Metals Considering Void Damage	52
Hydrothermal Coating of the Biodegradable Mg-2Ag Alloy	52
Investigation of the Mechanism of Powder Pool Coupled Activating TIG Welding	52