Materials Science-Poland

Papers
(The TQCC of Materials Science-Poland is 4. The table below lists those papers that are above that threshold based on CrossRef citation counts [max. 250 papers]. The publications cover those that have been published in the past four years, i.e., from 2022-07-01 to 2026-07-01.)
ArticleCitations
Role of crystallographic orientation in material behaviour under nanoindentation: Molecular Dynamics study54
NiTiO 3 /MnFe 2 O 4 ferrite composites: synthes22
A review of W-temper forming methods for high-strength 7xxx aluminum alloy sheet21
Insight into the microstructural stability and thermal fatigue behavior of nitrided layers on martensitic hot forging tools20
Microstructure and mechanical properties of selective laser melted 18Ni300 steel18
Maximizing the functional properties of epoxy coatings using milled Al for enhanced mechanical strength and corrosion resistance18
Performance studies of premixed blended hydraulic cement to revolutionize concrete production17
Stabilization of the metastable Cu-paratacamite phase using dual and triple nanostructures with titanium and zinc for improving its electrochemical applications16
Phosphor conversion for WLEDs: YBO 3 : Ce 3+ , Tb 3+ 16
Titanium dioxide nanotubes incorporated carboxymethyl cellulose 2D film and 3D scaffold for bone tissue treatment15
Cyclic loading test for brick masonry walls strengthened by steel mesh-ECC layers14
Evaluation of the possibility of improving the durability of tools made of X153CrMoV12 steel used in the extrusion of a clay band in ceramic roof tile production14
Experimental and first-principles investigation of high entropy superalloys produced by powder injection moulding method10
Nanofibrous membranes loaded with bupivacaine and carica papaya extract for pain management and wound healing in postoperative wounds10
Comparative evaluation of mechanical properties of short aramid fiber on thermoplastic polymers10
Shear and flexural strength of reinforced concrete beams made with recycled coarse aggregate concrete10
Erratum to “Fabrication and characterization of a 3D printing filament from polylactic acid and Cryptostegia grandiflora fibers”9
Effect of evaporation rate and substrate temperature on optical, structural, and electrical properties of ZnTe:Sb films deposited by thermal evaporation of Zn, Te, and Sb sources9
Comparison of the performance properties of commercially produced roller cone bit coatings9
Tribological performance of Orvar 2M tool steel coated with ALWIN XC for improved forging tool durability9
Antimicrobial activity, viability, and physicochemical properties of an MTA-type cement with different concentrations of bismuth trioxide9
Effect of carbon fiber surface treatment with HNO3 and KOH on the interfacial bonding of PMMA resin composite9
Study of synthesis parameters on the physical properties and morphology of smart PNIPAAm hydrogels8
Optimizing δ-ferrite structure to enhance high-temperature elongation in ER308L stainless steel deposited metal8
Production of pumice-containing nanofibers by electrospinning technique8
Analysis of the effect of curing and mixing periods on mechanical properties of the geopolymer composite8
Microstructure morphology and aging characteristics of 9% Cr martensitic heat-resistant steel after service8
Synthesis, microstructural evolution, and compaction behavior of Mg 30 -Al 25 -Ti 7
Corrosion resistance of PPTA Ni-based hardfacing layers7
Comparative study on different methods of activation of recycled powder grouts7
Synergistic emulsification of polyetheramine/nanofluid system as a novel viscosity reducer of acidic crude oil7
Non-isothermal melt- and cold-crystallization, melting process, and optical and mechanical properties of PLLA: the effect of TAPH6
Tin sulphide solar cells: An analysis using a theoretical method for an approximately 24% efficacy path6
Electrical resistance and self-sensing properties of pressure-sensitive materials with graphite filler in Kuralon fiber concrete6
Performance and microstructure of concrete containing green and LCD glass sand as fine aggregates6
Sliding elements made from biodegradable plastic – friction and wear of poly(lactic acid) compared to polyamide 66
Study of the possibility of using sulfur asphalt and sulfur concrete in road construction6
Fatigue tests of heat-treated rails in the R350HT grade5
Performance optimisation of the turning process along with multi-surface heating process5
A review of sheet warm forming methods for high-strength 7xxx aluminum alloys5
Application possibilities of scanning acoustic microscopy in the assessment of explosive welding5
Resveratrol and prednisolone loaded into human serum albumin nanoparticles for the alleviation of rheumatoid arthritis symptoms: an in vitro and in vivo study5
Retrofitting of heat-damaged fiber-reinforced concrete cylinders using welded wire mesh configurations5
Study on overlap rate and machinability of selected laser melting of maraging steel4
Flexural strength of low-strength RC beams using CFRP composite4
Studying CdS:In green phosphor's impacts on white-light emitting diode with higher luminous flux4
Enhancing pitting corrosion inhibition of AISI 304 stainless steel using a green frankincense-modified ferric chloride solution4
Lateral resolution enhancement in low-cost DLP 3D printing via integrated optical focusing and collimation4
Structural, morphological, and optical properties of Ag x O thin films deposited via obliquely angle deposition4
Evaluating the creep behaviour of plastic-processed aggregate-based concrete4
Influence of mechanical activation on the behavior of green high-strength mortar including ceramic waste4
Static friction of normal and reversed metal–polymer sliding pairs4
Investigation of silver nanoparticles embedded in extracted gelatins from camel, bovine, and fish bones for possible use in radiation dosimetry4
An experimental investigation of wire breakage and performance optimisation of WEDM process on machining of recycled aluminium alloy metal matrix composite4
Flexural behavior of precast concrete-filled steel tubes connected with high-performance concrete joints4
Compressive behavior of fiber-reinforced concrete strengthened with CFRP strips after exposure to temperature environments4
Design, fabrication, and optimization of magnetic vanadium MOF-embedded CMC–chitosan hydrogel beads for high-efficiency adsorptive removal of methyl violet 2B from aqueous media4
1.1061611175537