Journal of Asian Ceramic Societies

Papers
(The median citation count of Journal of Asian Ceramic Societies is 3. The table below lists those papers that are above that threshold based on CrossRef citation counts [max. 250 papers]. The publications cover those that have been published in the past four years, i.e., from 2022-05-01 to 2026-05-01.)
ArticleCitations
Enhancing Na ion conductivity of Na chloride cathode material NaFeCl 4 through polyatomic anion substitution36
Effect of sintering temperature on physical, mechanical, and electrical properties of nano silica particles synthesized from Indonesia local sand for piezoelectric application23
Magnetically separable CeO 2 /CoFe 2 O 4 heterojunction photocatalysts for dye degradation: cha19
Characterization of slurries for slip casting via constant pressure filtration: determination of the most suitable slurry property for controlling the green-body density18
Impedance spectroscopy technique for estimating the oxidation of the PyC interphase layer in a SiCf/SiC ceramic matrix composite18
High-voltage insulation and dielectric properties of ceramic-glass composites17
Enhancing the thermal shock resistance of Al2O3-SiC-C castables via the generation of in-situ SiC whiskers16
Enhancing the optical and photoelectric efficiency of PEDOT/PSS thin film by incorporating activated biochar for photovoltaic applications15
Sm 2 O 3 -doped 0.28PIN-0.32PZN-(0.4- x )PZ- 14
Effect of aprotic solvent on characteristics of Al2O3 ceramic hollow fiber substrates prepared by phase inversion for hydrogen permeation applications14
Effect of sintering temperatures on temperature coefficient of capacitance of KCa2Nb3O10 bulk-layered perovskite13
Crystallite size and phase purity in Pb 1-x Sr x TiO 3 ferroelectric perovskites for biomedical13
Effect of magnesium oxide in multiphase additive on the formation process and morphology of β-Si3N4 whisker11
Effect of CeO 2 -Y 2 O 3 sintering aids on the microstructure and properties of corundum-based 10
Microhardness and microstructural properties of a mixture of hydroxyapatite and β-tricalcium phosphate9
High energy-storage performance under low electric fields and enhanced electric-field-induced strain in Nb 5+ doped BNT−BT lead-free piezoceramics9
Structural evolution, ferroelectric phase transitions, and dielectric behavior of Sn-doped Ba 0.95 Sr 0.05 TiO 3<9
Influence of MgO-Al 2 O 3 hollow sphere content on the microstructure and mechanical properties of calcium hexaluminate porous cer8
Oxyfluorides for electrochemical and photoelectrochemical water oxidation: a review and basic tutorial8
Damage evolution in ceramics during the dwell/penetration transition under oblique impact loading8
Correlation between phase, microstructure and electrical properties of Ba 0.7 Sr 0.3 TiO 3 -mod8
A Synergic Effect of Bi-metallic Layered Hydro-Oxide Cocatalyst on 1-D TiO2 Driven Photoelectrochemical Water Splitting8
In-situ TiC-reinforced Ni-based composite coatings fabricated by ultrasonic-assisted electrospark powder deposition8
TiO 2 phase-controlled synthesis of Li-La-TiO solid electrolytes for advanced all-solid-state batteries7
Preparation and properties of HfB2-HfC and HfB2-HfC-MoB composites by reactive spark plasma sintering7
Hydrostatic piezoelectric properties of 1-3 type piezo-composite with a porous polymer matrix7
Effect of silver/zinc co-dopant on enhancing cytotoxicity and antibacterial property of spray pyrolyzed bioactive glasses7
Synthesis of BaTiO 3 /Ag nanocomposites using a sonochemical process and low-temperature sintering7
Effects of adding alloying elements to nickel on the hardening of WC–Ni cemented carbides7
Influence of Si 3 N 4 powder characteristics on the electrical and mechanical properties of pressu7
Facile synthesis of zinc hydroxyfluoride nanobelt and effect of hexamethylenetetramine for growth direction7
Effects of surface roughness of AlN ceramic substrate on the interface mechanical behavior of AlN/Ag structures7
In-situ formation of Zn-MOF coating on MgO/HA composite layer produced by plasma electrolytic oxidation on Mg-Sn-Mn-Ca alloy for orthopedic internal fixation devices7
Evaluation of surface characteristics and natural radioactivity of mineral-based glaze according to zircon substitution6
Investigating the ultralow dielectric loss of spinel-like and modified orthorhombic perovskite ceramic structures for microwave applications6
Parametric estimation analysis of compressive stress effects on piezoelectric properties of PZT ceramic6
Resistive switching behaviors of oxygen-rich TaOx films prepared by reactive magnetron sputtering6
Effect of laser surface texturing on friction performance and surface damage of silicon nitride ceramic6
Study on the correlation between radioactive counting time and measurement uncertainty of ceramic materials6
Tailoring the optical parameters of CuO nanoparticles via Ni and Co co-doping6
Development of oxide-based all-solid-state batteries using aerosol deposition6
High-temperature tribological performance of SiC p /Al composite5
Enhanced energy storage and fast discharge properties of BaTiO3-Bi(Ni0.5Zr0.5)O3 ceramics modified by (Bi0.5Na0.5)0.7Sr5
Preparation and properties of metakaolin-based porous geopolymer formed with sodium perborate5
Correction5
Synthesis of multi-type rare earth compounds with RE(OH)SO4 as a new sacrificial-template and photoluminescence5
Toward efficient dielectric material discovery: a comparative evaluation of Transformer and AutoML-based inverse learning5
Microstructures and properties of microporous magnesia aggregates from Mg(OH) 2 and magnesite5
Performance improvement of thin-film transistors with In2O3 channel engineering5
Green synthesis of ZnO nanoparticles by pineapple peel extract from various alkali sources4
An electromagnetic coupling treatment for improving the cutting performance of cemented carbide-coated tools4
Impact of stirring time and the corresponding growth mechanism in the solvothermal synthesis of WO3 nanostructures4
Effect of SiO2/Al2O3 ratio on sintering behavior, crystallization behavior and properties of diopside-anorthite glass-ceramics4
Cordierite-based ceramics from stevensite clay and coal fly ash4
Recent progress of porous geopolymers: nanoporosity regulation toward fundamental applications4
Research status and prospects of high-entropy composite ceramics4
Microstructural characterization of Ce-TZP/Al 2 O 3 after degradation in water4
Investigation of the preparation methods and mechanical properties of graphene nanoplatelets/α-SiC ceramic composites4
Synthesis, characterization, optical, and sensing investigations for Fe-BDC doped with 10 wt.% of activated food waste biochar4
High porosity and low thermal conductivity lanthanum zirconate porous ceramics via replica method4
The effect of SiC coatings microstructure on their infrared emissivity4
Preparation of ZnAl2O4 and its effect on fatigue resistance of alumina castables3
Nd-doped NASICON-type nanophosphors for near-infrared excitation and emission3
Effects of yttria doping on the interfacial reaction between barium zirconate ceramics and TiAl alloy melt3
Manufacturing of ceramic lightweight aggregates from oil-based drill cutting pyrolysis residues3
Effects of the Ni-Fe support microstructure on the electrochemical performance of the metal-supported solid oxide fuel cell3
From Champa unglazed pottery to Cham Bàu Trúc pottery: a comparative approach to technology and production3
Low temperature processed CO2 laser-assisted RF-sputtered GaN thin film for wide bandgap semiconductors3
Effect of AlN addition on the reaction sintering of Al2TiO5 composites fabricated by spark plasma sintering3
Low-temperature sintering of boehmite ceramics utilizing a hydraulic alumina precursor and the enhancement of mechanical properties by α-Al 2 O 3
Preparation of high-entropy nitride ceramics (TiVCrNbZr 1-x )N y by introducing nitrogen vacancies3
Crystal growth of HAp on plate-like ZnO particles using APTES as surface treatment agents3
Influence of ferric oxide content on performance of ferrosilicate glasses and glass fibers3
Tribology and in-vitro biological characterization of TiO2 addition on ceria stabilized zirconia-toughened alumina (CSZTA) composite3
Investigation of the bioactivity and antibacterial activity of porous hydroxyapatite ceramics derived from natural sources3
Effect of B 2 O 3 on structure, properties and tube forming of medium borosilicate pharmaceutical glasses3
High purity Al2O3 ceramic:Metallizing strategy, microstructure and sealing properties3
Achieving high energy storage performance and efficiency in lead-free SrTiO 3 ceramics via neodymium and lithium co-doping technique3
Development of hybrid multi-head, multi-material paste and ink extrusion type 3D printer for biomedical applications3
1.5559198856354