OOIR: Observatory of International Research

Papers

(The median citation count of Mechanics & Industry is 1. The table below lists those papers that are above that threshold based on CrossRef citation counts [max. 250 papers]. The publications cover those that have been published in the past four years, i.e., from 2022-01-01 to 2026-01-01.)

Article	Citations
Corrigendum for: Analytical modeling of residual stress in end-milling with minimum quantity lubrication	31
Pre-matching study of the natural gas engine turbocharging system based on the coupling of experiments and numerical simulation	15
Application of improved radar chart in the health evaluation model of hydraulic gate	11
Empirical formulation for bead shape prediction in direct energy deposition	11
Slip ratio control based on adaptive fuzzy sliding mode for vehicle with an electromechanical brake system	9
Experimental analysis of the leakage characteristics of an oil cooled electric motor L-shaped lip seal in high-speed conditions	9
The numerical simulation study of traction elevator steel belt model	9
Simulation of dieless clinching process considering the limit of blank holder	8
A multiple improved envelope spectra via feature optimization gram (MIESFO-gram) for diagnosis of compound fault signatures	8
Adaptive backstepping control for electro-hydraulic servo system in extension sleeve press-fitting process of bearing pressing machine	7
Study on contact load and preload characteristics of cylindrical roller bearings with triple-lobe raceway	7
A direct slicing method for optimized lattice structures	7
Characteristics of pressure signal of oil pulsating flow based on wavelet analysis	7
Study on elastohydrodynamic lubrication performance of double-layer composite water-lubricated bearings	6
Design and experimental verification of the picking cam mechanism for safflower filaments	6
Study of the industrial potential of Markforged X7 3D printer	5
A multi-model approach for wooden furniture failure under mechanical load	5
Estimation of thermophysic properties of a bimaterial by temperature field measurement and finite element model updating	5
On the response of re-entrant auxetic structure under dynamic crushing	4
Simulation on the effect of cylinder liner and piston ring surface roughness on friction performance	4
Study on the dynamic characteristics of planetary gear transmission mechanism of metal cold rolling mill	4
On the anti-missile interception technique of unpowered phase based on data-driven theory	4
A semi-implicit homogeneous discretized differentiator based on two projectors: experimental validation on a cable-driven parallel robot	4
Correlation analysis between coiling tension and the sleeve's hoop stress	4
Precise and coordinated gearshift control for AMT gearshift system equipped with two linear actuators	4

A mathematical framework to study the mechanical and cellular activity in regulating the fracture healing process	4
Research on bearing capacity of cross-type truss boom with variable cross-section of Crawler cranes	3
Empowering optimal transport matching algorithm for the construction of surrogate parametric metamodel	3
Characteristics of biodegradable polymers when subjected to ceramic coatings	3
Tolerance analysis of involute spur gear from the perspective of design	3
Harmonic modal analysis of hydroelectric runner in steady-state conditions: a Bayesian approach	3
Analysis on the influence law of traction speed on the cutting performance of coal containing hard concretion	3
Identification of key parameter influence on efficiency of chain drive for track cycling − Preliminary results	3
A new validated open-source numerical tool for the evaluation of the performance of wind-assisted ship propulsion systems	3
Reliability based design optimization of a two-stage wind turbine gearbox	3
Numerical simulation of single bubble motion fragmentation mechanism in Venturi-type bubble generator	3
Study of the efficiency of cavitation generating head with water removal system used to remove foulants from metal surface	3
Numerical investigation of thermal buckling and post-buckling behavior of an EN AW 6016-T4 car roof assembled in a steel body-in-white	3
Improved fuzzy neural network control for the clamping force of Camellia fruit picking manipulator	3
Verifying hyperparameter sensitivities of optimal filter design methods for fault signature enhancement	2
Agricultural tractors magneto-rheological seat suspension design based on LADRC control strategy	2
Active vibration control of a cable-driven parallel robot using active rods	2
Research on obstacle climbing gait structure design and gait control of hexapod wall climbing robot based on STM32F103 core controller	2
Research on custom-tailored swimming goggles applied to the internet	2
Sequential calibration of material constitutive model using mixed-effects calibration	2
Experimental study of the influence of the relative humidity of leaves and their link to adhesion losses in the wheel-rail contact	2
Lightweighting structures using an explicit microarchitectured material framework	2
Reliability evaluation of electromechanical braking system of mine hoist based on fault tree analysis and Bayesian network	2
Experimental quantification of heat haze errors in stereo-DIC displacements: Application to thermoplastics thermoforming temperature range	2
Verification of polynomial chaos surrogates in the framework of structural vibrations with uncertainties	2
Double-layer planning model for supply chain service combination of high-end equipment manufacturing industry	2
Wind turbine gearbox multi-scale condition monitoring through operational data	2
Aeroelastic scaling of flying demonstrators: mode tracking technique	1
Simplified dynamic modeling methodology for parallel shaft gear transmission system	1
A neural network-based data-driven local modeling of spotwelded plates under impact	1
Evolution of material removal in the magnetorheological polishing of Ti6Al4V by laser power bed fusion	1
Structure design and trajectory positioning method of underwater telescopic arm robot based on DE algorithm	1
Mechanical behavior of macroscopic interfaces for 3D printed multi-material samples made of dissimilar materials	1
Static reinforcement and vibration reduction of structures using topology optimization	1
Effects of cutting head load on fatigue life of bolter miner cutting arm	1
Vibration energy harvesting on a drone quadcopter based on piezoelectric structures	1
A study of AlSi5Cu3Mg alloy produced by laser powder bed fusion: porosity assessment, microstructure, mechanical properties	1
Video-based operational modal analysis of slender mechanical structures with neutral axis estimation via barycenter calculation	1
Evolution of physico-chemical and mechanical properties of bonded epoxy assemblies during hygrothermal cyclic aging	1
Wind-resistant stability of bridges with three-force coefficients based on deep learning under mountain conditions	1
Multi-objective optimization design of a heavy-duty folding mechanism and Self-discharging equipment development	1
A new method with ultrasonic mechanism for efficient depowdering of parts produced by electron beam melting	1
Study on prediction and optimization of gas–solid erosion on S-Zorb reactor distribution plate	1
Research on the motion trajectory control of industrial manipulators by the incremental PID control optimization algorithm	1
Method for holistic optimization of the manufacturing process numerically described as low-dimensional database	1
Vibrations of a dual-rotor system in aero-engine induced by the support misalignment	1
Toward steel strip insertion during wire arc additive manufacturing of aluminum alloy smart part	1
Dynamics behavior analysis of spatial parallel coordinate measuring mechanism with spherical clearance joints	1
Experimental study on influence of ultrasonic vibration on forming limit	1
Influence of Electric Cylinder Transmission Characteristics on Servo System	1

Fatigue life prediction of a piercing connector subject to breeze vibration and multi-field coupling	1
Research on cutting performance of micro-texturing tools for cutting aluminum alloys	1
Parametric-modeling-based multi-objective thermoelastic optimization of rudder structures	1
Numerical identification of the elasticity tensor of heterogeneous materials made of Silicon Carbide and Titanium by the Finite Element Model Updating (FEMU)	1
Numerical modeling of brittle mineral foam in a sacrificial cladding under blast loading	1
Inertia matching of CNC cycloidal gear form grinding machine servo system	1
Predicting high-fidelity data from coarse-mesh computational fluid dynamics corrected using hybrid twins based on optimal transport	1
Erratum to: Inertia matching of CNC cycloidal gear form grinding machine servo system	1
Improvement of arc burn defect of initial contact loss of electric hot incremental sheet forming	1
Research on the intelligent control system for lithium-ion aluminium shell power battery module stacking	1
Mechanical modeling of growth applied to Saccharomyces cerevisiae yeast cells	1
Preliminary modelling of power losses in roller chain drive: application to single speed cycling	1