OOIR: Observatory of International Research

Papers

(The TQCC of Mechanics & Industry is 1. The table below lists those papers that are above that threshold based on CrossRef citation counts [max. 250 papers]. The publications cover those that have been published in the past four years, i.e., from 2021-04-01 to 2025-04-01.)

Article	Citations
Elastic and damping characterization of open-pore metal foams filled or not with an elastomer for vibration control in turbomachinery	21
Corrigendum for: Analytical modeling of residual stress in end-milling with minimum quantity lubrication	11
Experimental study on influence of ultrasonic vibration on forming limit	9
Simulation on the effect of cylinder liner and piston ring surface roughness on friction performance	7
Shear buckling of ship plates with different holes	7
Evolution of material removal in the magnetorheological polishing of Ti6Al4V by laser power bed fusion	7
Vibration energy harvesting on a drone quadcopter based on piezoelectric structures	5
Damping coefficient calculation method for shore-side container cranes under the seismic conditions	5
Application of improved radar chart in the health evaluation model of hydraulic gate	4
Sequential calibration of material constitutive model using mixed-effects calibration	4
Mechanical modeling of growth applied to Saccharomyces cerevisiae yeast cells	4
Optimization of energy efficiency and NVH behaviour of a helical gear unit	3
A new method with ultrasonic mechanism for efficient depowdering of parts produced by electron beam melting	3
Multi-objective optimization of a small scale SCO₂ turbine rotor system with a shaft cooler	3
Numerical modeling of brittle mineral foam in a sacrificial cladding under blast loading	3
Evolution of physico-chemical and mechanical properties of bonded epoxy assemblies during hygrothermal cyclic aging	3
Research on obstacle climbing gait structure design and gait control of hexapod wall climbing robot based on STM32F103 core controller	2
Experimental study of the influence of the relative humidity of leaves and their link to adhesion losses in the wheel-rail contact	2
Pre-matching study of the natural gas engine turbocharging system based on the coupling of experiments and numerical simulation	2
Ride comfort investigation of semi-active seat suspension integrated with quarter car model	2
Lightweighting structures using an explicit microarchitectured material framework	2
A semi-implicit homogeneous discretized differentiator based on two projectors: experimental validation on a cable-driven parallel robot	2
Contribution to the formability improvement in sheet metal stamping by a novel technique to control press kinetics	1
Study on prediction and optimization of gas–solid erosion on S-Zorb reactor distribution plate	1
Active vibration control of a cable-driven parallel robot using active rods	1

Toward steel strip insertion during wire arc additive manufacturing of aluminum alloy smart part	1
A reduced order model to assist welding parameter setup	1
Parametric-modeling-based multi-objective thermoelastic optimization of rudder structures	1
Characterization and understanding of mechanical variability of elastomer: application in automotive valve testing in low cycles fatigue	1
Numerical simulation of single bubble motion fragmentation mechanism in Venturi-type bubble generator	1
Verification of polynomial chaos surrogates in the framework of structural vibrations with uncertainties	1
Precise and coordinated gearshift control for AMT gearshift system equipped with two linear actuators	1
Improvement of arc burn defect of initial contact loss of electric hot incremental sheet forming	1
Multi-objective optimization of process parameters for ultrasonic rolling extrusion of 42CrMo material	1
A method to manufacture spiral bevel gears by equivalent completing	1
Green-FFT model for 3D contacts considering microstructure and defects	1
Efficient transient dynamic analysis of a crane bridge subjected to shake table tests using non-linear substructuring	1
Empirical formulation for bead shape prediction in direct energy deposition	1
A neural network-based data-driven local modeling of spotwelded plates under impact	1
Research on bearing capacity of cross-type truss boom with variable cross-section of Crawler cranes	1
On the anti-missile interception technique of unpowered phase based on data-driven theory	1
Analytical modeling of residual stress in end-milling with minimum quantity lubrication	1
Evaluation of mechanical properties of Ni/BaTiO₃ functionally graded material	1
Dynamics behavior analysis of spatial parallel coordinate measuring mechanism with spherical clearance joints	1
On the response of re-entrant auxetic structure under dynamic crushing	1
Order component extraction technology for predictive maintenance system in rotary machine	1
Analysis on the influence law of traction speed on the cutting performance of coal containing hard concretion	1