OOIR: Observatory of International Research

Papers

(The H4-Index of Frontiers in Materials is 37. The table below lists those papers that are above that threshold based on CrossRef citation counts [max. 250 papers]. The publications cover those that have been published in the past four years, i.e., from 2022-05-01 to 2026-05-01.)

Article	Citations
Editorial: Machining technology and environmental degradation mechanism of surface microstructure of special materials, volume II	167
Editorial: 2022 retrospective: polymeric and composite materials	144
Energy dissipation properties of backfill materials under compaction in solid waste backfill mining	114
An experimental study on the impact resistance of a new three-wave beam steel guardrail	91
Design of a Wide-Angle and Polarization-Free 1-Bit Programmable Metasurface	89
Editorial: The role of polymer hydrogels in the bio-medical field	81
Analysis of the deterioration process of the dolomite with the interlayer in different directions during wetting	76
Creep subsidence prediction algorithm considering the effect of stress history for subgrades	76
High-efficiency adsorption of Cd2+ and Cr3+ by sodium vanadate nanowire arrays	75
Editorial: Editors’ showcase: Colloidal materials and interfaces	74
Effect of InxAl1-xAs graded buffer materials on pseudomorphic InP HEMT	72
Modified Charge Transport Model Under High-Frequency Unipolar Square Wave Voltage	72
Editorial: Preparation, Properties and Applications of Electro-Responsive Smart Materials	71
Editorial: Particle Interfaces & Interface Performance Materials	71
Analytical model for the load-slip relationship of bearing-shear connectors	68
Fabrication of polymeric composite GTR membrane from eggshell powder, polylactic acid and polyethylene glycol for periodontal application: in vitro evaluation	67
The corrosion behavior and tensile strength of the 2060 Al-Li alloy with different heat treatments	65
A 1-Bit Coding Metasurface With Polarization Conversion in X-Band	63
Dynamic cyclic fatigue resistance of NiTi instruments in a double-curved stainless steel canal with variable distances of displacement	57
Icy-hot: decoupled compute paradigm towards a general-purpose superconducting CPU design	55
Research on the coupling effect of film thickness and UV aging cycle on the rheological properties and microstructure evolution law of asphalt	52
Bibliographic trends in mineral fiber-reinforced concrete: A scientometric analysis	51
Failure modes and mechanical properties of double-layer rock-like composite specimens with a single fissure under triaxial compression	50
Editorial: Bioactive coatings: advancing bone implant performance and longevity	49
Influence of aggregate chemical composition on the demulsification rate of emulsified asphalt	47

Molecular simulation and experimental investigation on enhancement of microbe cement in municipal solid waste incineration fly ash	46
A bibliometric analysis and review on the performance of polymer-modified bitumen	46
Fabrication and performance of the wide-band highly shielded polyvinylidene fluoride film	45
Effect of different fly ash ratios on the mechanical properties of hybrid steel fiber reinforced concrete	44
Modeling of temperature dependence of Λ-graded InGaN solar cells for both strained and relaxed features	43
Full Lignin-Derived Electrospun Carbon Materials as Electrodes for Supercapacitors	42
Sol-gel synthesis of magnesium aluminate and synergistic degradation of Cr(VI) ion by adsorption and photocatalysis	41
MPX3 van der Waals magnets under pressure (M = Mn, Ni, V, Fe, Co, Cd; X = S, Se)	41
Utilization of sodium carbonate activator in strain-hardening ultra-high-performance geopolymer concrete (SH-UHPGC)	38
Adsorption of Ni2+, Cu2+ and Co2+ ions on coal gangue-based porous ceramics	38
Editorial: Deep learning in computational materials science	37
Multi-field numerical model and LSTM-based neural networks for thermal field predictions of concrete-filled steel tubes	37
Analysis of free and forced convections in the flow of radiative viscous fluid with oxytactic microorganisms	37